Manuals / Panasonic / Computer Equipment / Network Card

Panasonic AW-PH360N manual $ Mounting the camera, Stand-alone installation, Suspended installation

Models: AW-PH360N

1 52

Download 52 pages 54.4 Kb

Page 14

$ Mounting the camera

Installation (The installation work must be performed by your dealer without fail.)

$ Mounting the camera

The pan/tilt head’s camera mounting section has a mechanism for maintaining the camera’s balance that moves the camera mounting plate using a guide roller as a fulcrum. Use the described recommended lenses corresponding to the camera to be used. (Before mounting a lens other than recommended lenses, consult with your dealer.)

1.Change the position of guide pin A and/or the camera mounting screws in accordance with the following installation of the pan/tilt head before mounting the camera.

2.Adjust the balance by loosening the guide screws and moving the camera mounting plate.

3.Upon confirming the position where the balance is maintained, firmly tighten the guide screws. If the balance cannot be maintained, change the position of guide pin B or the positions of the guide screws, and adjust the balance again.

<Note>

OThe guide roller is fixed in place. Do not remove the guide roller screw.

<Stand-alone installation>

Camera mounting plate

Camera mounting screws

Guide pin A

Guide roller

Guide screw	Guide screw
	Guide pin B

<Suspended installation>

Guide pin A

Change the position of the camera mounting screws and the guide pin A to change the installation.

Camera mounting plate

Camera mounting screws

Guide roller

Guide screw	Guide screw
	Guide pin B

- 14 -

Image 14

Panasonic AW-PH360N manual $ Mounting the camera, Stand-alone installation, Suspended installation

Contents

Indoor Pan/Tilt Head Before attempting to connect, operate or adjust this productAW-PH360N Printed in Japan1 indicates safety information HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY1 indicates safety information FCC NoteIntroduction ContentsAccessories AccessoriesInstallation precautions Precautions for use Parts and their functions Parts and their functions 1 Tilting armStand-alone installation $ Assembling the pan/tilt headSuspended installation OAttaching the tilting armFor AW-RP605A For suspended installationFor stand-alone installation For a soft landingOWEB card settings $ Transmission signal selection settingOAnalog/IEEE1394 card settings OSDI settings3 When using the AW-RP400 controller $ Setting the cable compensation circuit of video signals2 When using the AW-RP605A controller $ Installing the pan/tilt head Safety wireSuspended installation $ Mounting the cameraStand-alone installation Mounting example when the lens side is heavy Stand-alone installationMounting example when the camera side is heavy Recommended lensesWith the AW-E655/AW-E750/AW-E860 OAttaching the chainWith the AW-E350/AW-E650 With the AW-E350/AW-E650 With the AW-E655/AW-E750/AW-E860 OAdjusting slack in the chainOMounting a camera Camera guide pin Camera mounting Screw Camera mounting Screw$ Connecting the connector panel with the controller AW-RP501 Connections$ Connecting the connector panel with the controller AW-RP505 Connections$ Connecting the connector panel with the controller AW-RP605A Connections$ Connecting the connector panel with the controller AW-RP400 ConnectionsConnections $ Connecting the connector panel RS-232C controlThe BNC connectors are not connected to the pan/tilt head DC cable UL Type SPT-2 2!164CAMERA I/F connector $ Head connector panel1ND/EXT connector 2 LENS I/F connector7 Y OUT connector 5 1394 connector6 CONTROL IN IP/RP connector 8 Pr/SDI OUT connectorVIDEO OUT connector 9 Pb OUT connectorG/L IN connector CAMERA CONTROL IN connectorDC 12V IN terminal board $ Connecting the AC adapter for use with the pan/tilt headConnections ? LAMP CONTROL terminal boardColor monitor $ Connection examplesConnections DC cablemax. 1640 ft. 500 m ConnectionsCamera cable supplied Color monitor Coaxial cable 10BASE-TConnections Connections Connections Connections Connections Coaxial cable BELDEN 8281, max.Color monitor 666 ft. 200 m ConnectionsCoaxial cable Camera cable supplied Coaxial cable BELDEN 8281, max. 3333 ft. 1000 mCable supplied with AW-CB400 Connectionspanel is used to control the camera DC cable UL Type SPT-2 2!16 AWG orConnections Connections Connections RS-232C cable AW-CA28T9 ConnectionsCamera cable supplied Color monitor Coaxial cable AC adapterConnections Connections For further details, refer to the web card instructionsConnections For further details, refer to the IEEE1394 card instructionsLimiters To release the setting $ Setting/releasing the limitersTo release the setting To release the settingTo release the setting To release the settingTo release the setting To release the settingTo release the setting To release the settingTo release the setting To release the setting$ Replacing the motor Replacement of consumable parts$ Replacing the battery $ Replacing the gearPower consumption DC +12 SpecificationsPower supply Maximum load capacity 8.8 lb 4 kg Allowable operating temperatureWeight $ Functions/performanceSpecifications Allowable operating humidityPage