IBM 715 P/N - 13H6715 manual Preparing for Software Installation, Installing the Software

Page 7

PREPARING FOR SOFTWARE INSTALLATION

If you are upgrading from the Multimedia Modem or have any other Mwave software installed in your computer, you must remove the old Mwave software to avoid conflicts with the new Mwave software. The setup program that is part of your installation package should be used to remove the old Multimedia Modem Mwave software from your hard disk drive.

INSTALLING THE SOFTWARE

Note: If you are upgrading from the Multimedia Modem or have any other Mwave software installed in your computer, you must remove the old Mwave software to avoid conflicts with the new Mwave software. The setup program that is part of your installation package should be used to remove the old Multimedia Modem Mwave software from your hard disk drive.

You can use the Multimedia Modem Plus with the following operating systems:

!DOS 5.0 or higher

!Microsoft Windows 3.1 or 3.11 under DOS 5.0 or higher

!Microsoft Windows 95

!OS/2 Warp with Windows or WIN-OS/2 installed

NOTE: During the installation process some message windows (boxes) may appear which are not addressed in this documentation, choose the default to proceed with the install process.

WHAT TO DO NEXT

!If you are installing or updating under any version of Windows, go to "Installing the Software Under Windows 3.x or Windows 95."

!If you are installing or updating under OS/2 Warp, go to "Installing the Software Under OS/2 Warp."

!If you are installing WIN-OS/2 support under OS/2 Warp with Windows application support (Blue Spine), install OS/2 support first. Then install Windows support from a WIN-OS/2 full screen session.

!If you are installing WIN-OS/2 support under OS/2 Warp for Windows (Red Spine), install Windows first in native DOS/Windows, then install OS/2 support using the Windows configuration values.

!If you are installing QuickLink Message Center or software applications that are not part of this package, read "Installing Applications Software."

Page 7 of 47

Image 7
Contents First Edition December MOD 715 P/N 13H6715Table of Contents Helpful Hints Introduction About this BookBefore YOU Begin Mwave Software FeaturesRelease Information Minimum System Requirements Installing the Software Preparing for Software InstallationWhat to do Next \SETUP Installing the Software Under Windows 3.X or WindowsPage Configuring Your Multimedia Modem Plus for Windows Manually Configuring Your Multimedia Modem Plus for Windows Configuring Mwave DOS Installing the Software Under OS/2 Warp Page Configuring Your Multimedia Modem Plus for OS/2 Warp Page Updating the MMPM/2 for Multimedia Modem Plus Configuring Your Multimedia Modem Plus for WIN-OS/2 Uninstalling Multimedia Modem Plus Software Installing Applications SoftwarePage Manual Discrimination Using VOICE, FAX and DataCaller ID Setting Mwave Discriminator OptionsOptions Caller ID IdentificationDtmf Code Dtmf Code DiscriminationSettings Discriminator SettingsUsing Mwave Dsvd Using IBM WAKE-UP on RingUsing the Mwave Modem Using Audio Using the Mwave Modem Command ReferenceSetting Windows Audio Controls MIC Line Controlling Volume and BalanceSetting Tone Controls Selecting the Input SourceOS/2 Audio Controls Adding Special Audio EffectsUsing the Fastcfg Screen Using DOS ApplicationsPlaying a CD Freeing Memory for DOS Applications Using the Jpeg Image Viewer Installation Problems TroubleshootingProblem Operation ProblemsCannot connect to a DOS modem and fax application Helpful Hints Installation\PS1TOOLS\PS1START.BAT DEVICE=C\DSP2\SOLO\MWDDSOLO.EXE Faxworks for OS/2 Users Audio Applications Supported Internal CD-ROM Drives SpecificationsCard Features Internal I/O ConnectionsTelephony Subsystem Power RequirementsFAX Modem Data ModemIBM Multimedia Modem Plus Settings Table Audio FeaturesRecomended Settings for the Ambra Series Glossary of Terms and Abbreviations Page License Information MNP TrademarksIBM WIN-OS/2