IBM MaxLoader manual Programming Adapter Manufacturers, Eprom Emulator Manufacturers

Page 110

MaxLoader User’s Guide

9. Programming Adapter Manufacturers

Compass Systems (Asia)	www.compass21.com
EE Tools, Inc	www.eetools.com
Emulation Technology	www.1800adapter.com
Emulation Solutions	www.adapters.com
Logical System	www.logicalsys
Iron Wood	www.ironwoodelectronics.com

10. EPROM Emulator Manufacturers

EE Tools, Inc	www.eetools.com
Tech Tools	www.tech-tools.com

8. OTHER PRODUCTS

Optional EPROM Emulator

EeRom-8U: Memory Emulation System for R&D and Engineering Part

.	Communication –USB Port (1.1)

-Operation Software-Wind98/ME/2000/XP/Vista

-Low Voltage Supports-3.3V/5V

-Target Connect - 32Pin Dip Cable (Standard)

-32Pin PLCC POD (Option)

-Buffer Memory – 8M, 12ns SRAM (8bit)

-Download Speed – 1Mbyte/sec

-Reset Signal – Low/High Software Control

-Supports Device – E/EPROM: 2764-27080, 2864-28256 Flash Memory: 29512-29040

-Size – 98x 63x 22 (mm)

The requirement to use the Window graphical application is:

Processor: IBM PC or Compatible Pentium/100 MHz or better.

	RAM	: 5MB
	DISK	: 5MB

110

Image 110

Contents MaxLoader User’s Guide Quick Start Examples Device Config Trouble Shooting & Technical Support Glossary Other ProductsAbout Nand Flash Memory Programmer Models for PC USB Interface EE Tools, IncMaxLoader User’s Guide About This Manual General DescriptionTo Start the windows software Hardware InstallationTo Install the software from a CD drive MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide To install the Software for parallel port programmers Select Product Families of Programmable Devices NVM HierarchyFlash Memory Flash Memory Technologies Serial Eeprom Performance ComparisonSerial Flash Eeprom ƒ Xilinx 17xx familyNon-Typical Devices 8-bit 1-Megabits Bit 1-Megabits Erasing an EpromPLD Features Microcontroller About Device ID and Auto Select on EE Tools programmers Auto SelectTo Find a Device ID Safety Note Conventions Other terms and definitions are as followsChoosing a Right Adapter Different Device Packages Different Programming Adapters Quick Start Examples Programming an Eprom with dataMaxLoader User’s Guide Duplicating an Eprom from a master IC device Source Device Programmed AMD 27C256Split Basic Menu Screen Information Option InformationTarget Device Erased or blank Intel 27C256 Counter Additional Option Information for Non PLD DevicesSystem Information Verification error Fileƒ Binary Format ƒ Intel HEX Format ƒ Motorola S HEX Format ƒ Tektronix HEX Format 00001102444154414D414E2053332053455249414C8F 01000001ƒ Jedec Standard PLD devices only ETX Sum Checkƒ POF file Altera EPMxxx devices only File / LoadFile / Reload File/ Load Project File/ Save ProjectFile/ Save Log File/ Save All Messages Buffer Asc Data looking for Ascii value Buffer / Edit BufferFind HEXFill random data Find NextFill Buffer Copy buffer Clear buffer Set editor to view mode Print bufferSet editor to edit mode Set Editor to binary modeSet editor to 8 bitbyte Hex Set editor to 16 bitword HexSet default editor mode Set editor to 32 bitdouble word HexSet default Reset Editor Swap nibbleSwap byte Swap WordSwap double word Jedec editorClear Close Buffer / Edit UESDevice / Select by history Select ƒ Select / E EPROM, Flash Select / Auto SelectSelect / Device information Device / Change Algorithm Device / Auto Menu Option Device / Blank CheckMaxLoader User’s Guide ƒ Programmable Logic Device operation Device / Programƒ Memory device ƒ 28C256, 28C010, etcƒ Microchip PIC devices Copy from a master chip to a new chipƒ Atmel or Xilinx ƒ Motorola MC68HC908 devicesƒ Serial EEPROMs Device / Read Device / VerifyDevice / Security Device / Data CompareDevice / Erase Device / Encryption Device / OptionDram types tested Device / AutoTest / RAM Test Sram type testedTest / Vector Test Optional Operation Value DelayTest / IC Test VccConfig / Select Product TestConfig / Config Option Config Option / Buffer Clear Before File LoadingConfig Option / verify after programming Config Option / Blank Check Before ProgrammingConfig Option / Verify After Reading Config Option / Byte order swappingByte swap = disabled Cursor AT Location 00000000 8 BIT AddressingConfig Option / Device Insert Test Config Option / Device ID CheckConfig Option / 32 Bit Checksum Config Option / SoundConfig Option / Default Buffer Value Config Option / Port TopMax, ChipMax Config Option / USB Option USB programmer USB option / Enable Start buttonUSB option / Good LED off on socket open USB option / Enable Start ALL buttonEnabling #4 socket to be master socket Config Option / Gang Split Select Split Byte $0001 Byte $0003Config Option / Address Device Address File LoadConfig Option / Auto Inc File SaveConfig / Concurrent gang mode Config / Hardware testMaxLoader User’s Guide Enabling any button to be a Start Key Close How to program write one file into different sockets ? Example 1 Program 8 of 27128 Eproms with Same Data MaxLoader User’s Guide MaxLoader User’s Guide Example 2 SET Program for 8 of 27128 Eproms MaxLoader User’s Guide Config / Enter Production Mode Config / Enter Supervisor ModeConfig / Set Password Config / LanguageRegistration Software UpdatesTesting the Hardware Quick Self-Diagnostics Contacting Customer Support Service Information Electronic Engineering Tools, IncLimited One-Year Warranty Useful Web Site Addresses/ Phone Numbers Programming Adapter Manufacturers Eprom Emulator ManufacturersAbout Nand Flash Memory Why Nand Flash How to Program Nand FlashHow to Read Nand Flash BGAGAL DIPFpga Jedec file HEX fileJedec LCCPlcc OTPPGA RAM PqfpQFP ROMUV Erasable TQFTsop Verify