IBM MaxLoader manual Config Option / Auto Inc, File Save

Page 91

MaxLoader User’s Guide

-File Offset is subtracted from addresses from the file downloaded to the programmer. For example, if you set File Offset to 1000h, then the downloaded data minus 1000h would be placed into the buffer at the address specified by the Buffer Start Address.

-Buffer Start Address is the address in the buffer where you want your downloaded data to start. For example, if you set Buffer Start Address to 800h, then the downloaded data only appears in the buffer beginning at address 800h.

File Save

These addresses will be applied for programming the buffer data. -Buffer Start: Starting address for data to be saved.

-Buffer End: Ending address for data to be saved.

Config Option / Auto Inc

The feature allows users to program a certain area that might contain a serial number in the memory device with serialized number by a certain value.

Start: Start address of memory that contains serialized data

End: End address of memory

91

Image 91

Contents MaxLoader User’s Guide Quick Start Examples Device Config Trouble Shooting & Technical Support About Nand Flash Memory Other ProductsGlossary EE Tools, Inc Programmer Models for PC USB InterfaceMaxLoader User’s Guide General Description About This ManualTo Install the software from a CD drive Hardware InstallationTo Start the windows software MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide To install the Software for parallel port programmers Select Product NVM Hierarchy Families of Programmable DevicesFlash Memory Flash Memory Technologies ƒ Xilinx 17xx family Performance ComparisonSerial Flash Eeprom Serial EepromNon-Typical Devices 8-bit 1-Megabits Erasing an Eprom Bit 1-MegabitsPLD Features Microcontroller Auto Select About Device ID and Auto Select on EE Tools programmersTo Find a Device ID Other terms and definitions are as follows Safety Note ConventionsChoosing a Right Adapter Different Device Packages Different Programming Adapters Programming an Eprom with data Quick Start ExamplesMaxLoader User’s Guide Source Device Programmed AMD 27C256 Duplicating an Eprom from a master IC deviceTarget Device Erased or blank Intel 27C256 Basic Menu Screen Information Option InformationSplit System Information Additional Option Information for Non PLD DevicesCounter File Verification errorƒ Binary Format ƒ Intel HEX Format ƒ Motorola S HEX Format 00001102444154414D414E2053332053455249414C8F 01000001 ƒ Tektronix HEX Formatƒ Jedec Standard PLD devices only Sum Check ETXFile / Load ƒ POF file Altera EPMxxx devices onlyFile / Reload File/ Save Project File/ Load ProjectFile/ Save Log File/ Save All Messages Buffer HEX Buffer / Edit BufferFind Asc Data looking for Ascii valueFill Buffer Find NextFill random data Copy buffer Clear buffer Print buffer Set editor to view modeSet Editor to binary mode Set editor to edit modeSet editor to 16 bitword Hex Set editor to 8 bitbyte HexSet editor to 32 bitdouble word Hex Set default editor modeSwap nibble Set default Reset EditorSwap Word Swap byteJedec editor Swap double wordClear Buffer / Edit UES CloseDevice / Select by history Select Select / Auto Select ƒ Select / E EPROM, FlashSelect / Device information Device / Change Algorithm Device / Blank Check Device / Auto Menu OptionMaxLoader User’s Guide ƒ 28C256, 28C010, etc Device / Programƒ Memory device ƒ Programmable Logic Device operationCopy from a master chip to a new chip ƒ Microchip PIC devicesƒ Serial EEPROMs ƒ Motorola MC68HC908 devicesƒ Atmel or Xilinx Device / Verify Device / ReadDevice / Erase Device / Data CompareDevice / Security Device / Option Device / EncryptionSram type tested Device / AutoTest / RAM Test Dram types testedTest / Vector Test Vcc DelayTest / IC Test Optional Operation ValueTest Config / Select ProductConfig Option / Buffer Clear Before File Loading Config / Config OptionConfig Option / Byte order swapping Config Option / Blank Check Before ProgrammingConfig Option / Verify After Reading Config Option / verify after programmingCursor AT Location 00000000 8 BIT Addressing Byte swap = disabledConfig Option / Device ID Check Config Option / Device Insert TestConfig Option / Default Buffer Value Config Option / SoundConfig Option / 32 Bit Checksum Config Option / Port TopMax, ChipMax USB option / Enable Start button Config Option / USB Option USB programmerEnabling #4 socket to be master socket USB option / Enable Start ALL buttonUSB option / Good LED off on socket open Config Option / Gang Split Select Byte $0001 Byte $0003 SplitConfig Option / Address File Load Device AddressFile Save Config Option / Auto IncConfig / Hardware test Config / Concurrent gang modeMaxLoader User’s Guide Enabling any button to be a Start Key Close How to program write one file into different sockets ? Example 1 Program 8 of 27128 Eproms with Same Data MaxLoader User’s Guide MaxLoader User’s Guide Example 2 SET Program for 8 of 27128 Eproms MaxLoader User’s Guide Config / Enter Supervisor Mode Config / Enter Production ModeConfig / Language Config / Set PasswordTesting the Hardware Software UpdatesRegistration Quick Self-Diagnostics Contacting Customer Support Electronic Engineering Tools, Inc Service InformationLimited One-Year Warranty Useful Web Site Addresses/ Phone Numbers Eprom Emulator Manufacturers Programming Adapter ManufacturersAbout Nand Flash Memory How to Program Nand Flash Why Nand FlashBGA How to Read Nand FlashFpga DIPGAL LCC HEX fileJedec Jedec filePGA OTPPlcc ROM PqfpQFP RAMVerify TQFTsop UV Erasable