IBM 2289, 6824 manual Safety Information, To connect To disconnect

Page 7

Safety Information

DANGER

Electrical current from power, telephone, and communication cables is hazardous.

To avoid a shock hazard:

vDo not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

vConnect all power cords to a properly wired and grounded electrical outlet.

vConnect to properly wired outlets any equipment that will be attached to this product.

vWhen possible, use one hand only to connect or disconnect signal cables.

vNever turn on any equipment when there is evidence of fire, water, or structural damage.

vDisconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

vConnect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

To connect:

To disconnect:

1.

Turn everything OFF.

1.

Turn everything OFF.

2.

First, attach all cables to devices.

2.

First, remove power cords from outlet.

3.

Attach signal cables to connectors.

3.

Remove signal cables from connectors.

4.

Attach power cords to outlet.

4.

Remove all cables from devices.

5.

Turn device ON.

 

 

 

 

 

 

DANGER

Le courant électrique provenant de l’alimentation, du téléphone et des câbles de transmission peut présenter un danger.

Pour éviter tout risque de choc électrique :

vNe manipulez aucun câble et n’effectuez aucune opération d’installation, d’entretien ou de reconfiguration de ce produit au cours d’un orage.

vBranchez tous les cordons d’alimentation sur un socle de prise de courant correctement câblé et mis à la terre.

vBranchez sur des socles de prise de courant correctement câblés tout équipement connecté à ce produit.

vLorsque cela est possible, n’utilisez qu’une seule main pour connecter ou déconnecter les câbles d’interface.;

vNe mettez jamais un équipement sous tension en cas d’incendie ou d’inondation, ou en présence de dommages matériels.

vAvant de retirer les carters de l’unité, mettez celle-ci hors tension et déconnectez ses cordons d’alimentation, ainsi que les câbles qui la relient aux

© Copyright IBM Corp. 2002

v

Image 7
Contents User Guide Type 2289 Page User Guide Type 2289 Page Appendix B. Manual modem Iv User Guide To connect To disconnect Safety InformationModem safety information Lithium battery noticeConnexion Déconnexion Consignes de sécurité relatives au modem Laser compliance statementViii User Guide Information resources OverviewUser Guide Features Installing optionsAudio subsystem Security features Specifications Tools required Available optionsHandling static-sensitive devices Installing external options Locating the connectors on the front of your computer Locating the connectors on the rear of your computer Obtaining device drivers Connector DescriptionRemoving the cover Identifying parts on the system board Locating componentsInstalling memory What to do next Installing adapters Installing internal drives Drive specifications Installing a drive Connecting the first IDE CD-ROM drive or DVD-ROM drive Physical security Connecting an additional IDE CD-ROM drive or DVD-ROM driveChanging the battery Replacing the cover and connecting the cables Erasing a lost or forgotten password clearing Cmos Installing options User Guide Exiting from the IBM Setup Utility program Using the IBM Setup Utility programStarting the IBM Setup Utility program Viewing and changing settingsUsing Security Profile by Device User passwordAdministrator password Setting, changing, and deleting a passwordSelecting a temporary startup device Selecting a startup deviceChanging the startup device sequence User Guide System programs Updating flashing Bios from a disketteUpdating flashing Bios from your operating system Appendix A. Updating System ProgramsRecovering from a POST/BIOS update failure Basic AT commands Appendix B. Manual modem commandsExtended AT commands Force DSR Signal High on Guard tone disabledEnable RTS/CTS hardware flow control US setting for off-hook-to-on-hook ratioFax Class 1 commands MNP/V.42/V.42bis/V.44 commandsFax Class 2 commands Voice commands User Guide Address range Address range hex Size Description Decimal Appendix C. System address mapsSystem memory map Address mapLPT3 Address hex Description Bits Byte pointer DMA I/O address mapAddress hex Description Bits Byte pointer DMA channel Data width System resource System resourceUser Guide Television output notice Appendix E. NoticesIBM TrademarksDVD IndexPage Page Part Number 49P1040