Fujitsu 5000 user manual Connection

Page 27

2 Connection

Connect the display, keyboard, and power cord to the PC.

WARNING

● Connect the grounding leads to the device that needs to be grounded before turning it on.

You may get electrical shock if you do not provide grounding.

Do not connect the grounding wire to the gas pipe.

Otherwise it may cause a fire.

● Turn the PC and attached devices off and unplug power cords from their power outlet before installing or uninstalling the display, keyboard, mouse and others.

Otherwise it may cause an electric shock.

● Use the genuine Fujitsu products for display, keyboard and mouse.

Otherwise, it may cause an electric shock or fire.

CAUTION

● Make sure that you connect the cable correctly.

The PC and peripheral devices may be damaged, if they are connected with wrong cables.

● Do not use the service receptacle for plugging of a peripheral device not listed on the manual.

Or, it may cause a fire or a failure.

● Hold the PC board by touching the specified sections only.

Otherwise, personal injury or a fault may occur.

14

Image 27

Contents Deskpower 5000 Series User’s Manual Important Safety Instructions Iii For Safe Operation Before reading this manualBacking Up the Data Using this Product for High-Safety ApplicationsMicrosoft Service Pack Point Conventions Used in This ManualDiskcopy a a Command entry keyingCD-ROM drive\setup.exe Screenshot example and illustrations Representation for Bios SetupReference to products Disposal of batteries RecyclingDisposal of the PC unit Disposal of the LCD unitRear of the PC main unit Before Reading This Manual Organization of This ManualContents List of Specifications Before Installing a Peripheral Device Removing the CoverInstalling Memory Modules Installing an Expansion CardChapter Front of the PC Unit Power buttonPower lamp Part Names and FunctionsFloppy disk access lamp Disk access lampUSB connector CD access lampExpansion card slots Keyboard connector Connect the keyboardRear of the PC Unit Burglarproof lockLine in terminal Serial connectorParallel connector CRT connectorPower supply unit Inside the PC UnitInternal hard disk drive Motherboard Secondary IDE connector IDE2Floppy disk drive connector FDD Primary IDE connector IDE1 Internal batteryInstallation Connection Mounting Feet InstallationLocation of Installation Vertical PlacementPage Example of Installation Point Connection Connecting the mouse Connecting the Display/Keyboard/MousePlugging the power cord into power receptacle Plugging the power cord into inlet of display unitConnecting the display cable to the PC unit Connecting the keyboardConnect the Power Cord Page Power On How to Power On Considerations Setting UpClick Ignore Setting Up Windows XPTurn on the PC Click NextTurn on the computer Setting Up Windows PointClick Perform Click OK. The PC restartsClick User for this computer... and Next Click Standard setting and NextSelect Restart and click OK Problem During Setup? How to Turn Off Turn Off the ComputerFor Windows XP For Windows Me For WindowsHardware Keyboard Alt key Caps Lock keyCtrl key Windows keyGuidelines for CD Media CDsPull the tray out with a hand Inserting or Removing a CDInserting a CD Press the CD eject buttonManually push the tray until it clicks Removing the CDFloppy Disks Inserting or Removing a Floppy Disk PointInserting a Floppy Disk Removing a Floppy Disk Make sure that the floppy disk access lamp is offHard Disk Remove the ball and clean it with water Maintenance of the HardwareMaintenance of the PC Unit Maintenance of the MouseClean the inside of the mouse Maintenance of the KeyboardCleaning CDs Cleaning the Floppy Disk DriveSystem Expansion Before Installing a Peripheral Device Use an appropriate screwdriver Removing the Cover Removing the CoverRemove the two screws on the PC unit Remove the upper cover Installing Memory Modules Memory Module Combinations Location of Memory Modules Applicable Memory ModulesInstalling Memory Modules Point Installing an Expansion Card Installing an Expansion Card Location of expansion Cards Applicable Expansion CardsUnplug the PC Remove the upper cover Remove the slot cover Remove the expansion card mounting bracketPlug the PC Turn on the PC Install the expansion card mounting bracketReinstall the upper cover Insert the expansion card into the slotTechnical Information PC Specifications List of SpecificationsCPU CSMA/CD LAN functionCRT connector Connector SpecificationsParallel connector LAN connector 100BASE-TX/10BASE-TSerial connector Mouse connectorKeyboard Connector Glossary Symbol

Related manuals

Manual 82 pages 52.81 Kb