Fujitsu 5000 user manual Iii

Page 3

13.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.

e.If the product has been dropped or the cabinet has been damaged.

f.If the product exhibits a distinct change in performance, indicating a need for service.

14.CAUTION. When replacing the battery, be sure to install it with the polarities in the correct position. There is a danger of explosion if the battery is replaced with an incorrect type or is mistreated. Do not recharge, disassemble or dispose of in fire. Replace only with the same or equivalent type recommeded by the manufacturer. Dispose of the used battery according to the manufacturer’s instructions.

15.Use only the proper type of power supply cord set (provided in your accessories box) for this unit. It should be a detachable type: UL listed/CSA certified, BS1363,ASTA,SS145 certified, rated 10A 250V minimum, VDE approved or its equivalent. Maximum length is 15 feet (4.6 meters).

16.NOTE:

Please take extra precaution when connecting the LAN cable; do not connect the LAN cable to the peripheral device’s connector, that might have excessive voltage.

iii

Image 3
Contents Deskpower 5000 Series User’s Manual Important Safety Instructions Iii For Safe Operation Before reading this manualBacking Up the Data Using this Product for High-Safety ApplicationsMicrosoft Service Pack Point Conventions Used in This ManualDiskcopy a a Command entry keyingCD-ROM drive\setup.exe Screenshot example and illustrations Representation for Bios SetupReference to products Disposal of batteries RecyclingDisposal of the PC unit Disposal of the LCD unitRear of the PC main unit Before Reading This Manual Organization of This ManualContents List of Specifications Before Installing a Peripheral Device Removing the CoverInstalling Memory Modules Installing an Expansion CardChapter Front of the PC Unit Power buttonPower lamp Part Names and FunctionsFloppy disk access lamp Disk access lampUSB connector CD access lampExpansion card slots Keyboard connector Connect the keyboardRear of the PC Unit Burglarproof lockLine in terminal Serial connectorParallel connector CRT connectorPower supply unit Inside the PC UnitInternal hard disk drive Motherboard Secondary IDE connector IDE2Floppy disk drive connector FDD Primary IDE connector IDE1 Internal batteryInstallation Connection Mounting Feet InstallationLocation of Installation Vertical PlacementPage Example of Installation Point Connection Connecting the mouse Connecting the Display/Keyboard/MousePlugging the power cord into power receptacle Plugging the power cord into inlet of display unitConnecting the display cable to the PC unit Connecting the keyboardConnect the Power Cord Page Power On How to Power On Considerations Setting UpClick Ignore Setting Up Windows XPTurn on the PC Click NextTurn on the computer Setting Up Windows PointClick Perform Click OK. The PC restartsClick User for this computer... and Next Click Standard setting and NextSelect Restart and click OK Problem During Setup? How to Turn Off Turn Off the ComputerFor Windows XP For Windows Me For WindowsHardware Keyboard Alt key Caps Lock keyCtrl key Windows keyGuidelines for CD Media CDsPull the tray out with a hand Inserting or Removing a CDInserting a CD Press the CD eject buttonManually push the tray until it clicks Removing the CDFloppy Disks Inserting or Removing a Floppy Disk PointInserting a Floppy Disk Removing a Floppy Disk Make sure that the floppy disk access lamp is offHard Disk Remove the ball and clean it with water Maintenance of the HardwareMaintenance of the PC Unit Maintenance of the MouseClean the inside of the mouse Maintenance of the KeyboardCleaning CDs Cleaning the Floppy Disk DriveSystem Expansion Before Installing a Peripheral Device Use an appropriate screwdriver Removing the Cover Removing the CoverRemove the two screws on the PC unit Remove the upper cover Installing Memory Modules Memory Module Combinations Location of Memory Modules Applicable Memory ModulesInstalling Memory Modules Point Installing an Expansion Card Installing an Expansion Card Location of expansion Cards Applicable Expansion CardsUnplug the PC Remove the upper cover Remove the slot cover Remove the expansion card mounting bracketPlug the PC Turn on the PC Install the expansion card mounting bracketReinstall the upper cover Insert the expansion card into the slotTechnical Information PC Specifications List of SpecificationsCPU CSMA/CD LAN functionCRT connector Connector SpecificationsParallel connector LAN connector 100BASE-TX/10BASE-TSerial connector Mouse connectorKeyboard Connector Glossary Symbol
Related manuals
Manual 82 pages 52.81 Kb