Fujitsu 5000 user manual Power On

Page 32

3 Power On

￿ Cautions

● When turning on the PC for the first time after purchase, do not connect any peripheral equipment.

● The power lamp shines orange when the PC is in the standby mode.

● Before turning the PC power switch ON, make sure that the display unit has been connected to the PC. If the display unit is not connected, it is not recognized when you turn the PC power switch on. In such case, the on-screen display may be abnormal when the display unit is connected later. If you use an analog display unit, attach it to the PC. Then, terminate the OS, turn the PC power switch off, and turn it on again.

● If you use a digital display unit by plugging its power cord directly to the power receptacle, make sure that the power switch of the digital display unit is turned on before you turn the PC power switch on. If you turn the PC power switch on before turning on the power switch of digital display unit, nothing appears on the screen. In such case, turn the PC power switch off first, then turn the display and PC power switches on in the correct sequence.

● If you have connected the display power cord to the PC, the display unit is turned on when

you turn the PC power switch on. Therefore, you need not use the display power button later once you have pressed it.

The display unit is turned on just when you turn the PC power switch on in the step 2.

● If the window does not appear at the center of screen, check the display frequency for a setup error and correct it from the Control Panel of the PC. If the error continues, fine-adjust the window position using the controls of the display unit.

● If you need to turn the PC power switch off immediately after its power-on, wait until the OS starts up. Then, shut down the PC by following the “Turn off the computer”.

● The PC screen may be distorted or it may show horizontal lines when starting to display the image or when changing the display mode (for example, when starting up or shutting down the Windows, or when recovering from the energy saving mode). This is not a fault, you can continue to operate.

● When the FUJITSU logo continues on the screen after you have turn the PC power switch on, the PC is checking its built-in devices by running the POST (Power-On, Self-diagnostic Test). Do not turn the PC power switch off during the POST. If a problem is found during the POST, its error message is displayed.

● The PC screen may be distorted or it may show horizontal stripes instantaneously when the system starts up (including unpacking contract) or shut down. This is not a fault, you can continue to operate.

● If you have added a peripheral device to the PC, do not turn the PC power switch on while the PC upper cover is open.

● After you have turned the PC power switch off, wait at least 10 seconds before turning it on again. ● Check the following, if the screen is blank.

● The display power switch is turned on. ● The energy saving mode is not set.

Move the mouse or press any key. The PC may be shifted to S3 in the ACPI mode, if the standby lamp is orange. Press the power button. If the screen remains blank 30 seconds after you press the power button, then hold down the power button to turn the PC off.

● The display signal cable is connected correctly.

● The display power cord is plugged into the power receptacle.

● The display brightness and contrast controls are adjusted correctly. If not, adjust the screen with the

brightness and contrast controls.

19

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Deskpower 5000 Series User’s Manual Important Safety Instructions Iii Before reading this manual For Safe OperationUsing this Product for High-Safety Applications Backing Up the DataMicrosoft Service Pack Conventions Used in This Manual PointCommand entry keying CD-ROM drive\setup.exe Screenshot example and illustrationsRepresentation for Bios Setup Diskcopy a aReference to products Recycling Disposal of the PC unitDisposal of the LCD unit Disposal of batteriesRear of the PC main unit Organization of This Manual Before Reading This ManualContents Before Installing a Peripheral Device Removing the Cover Installing Memory ModulesInstalling an Expansion Card List of SpecificationsChapter Power button Power lampPart Names and Functions Front of the PC UnitDisk access lamp USB connectorCD access lamp Floppy disk access lampKeyboard connector Connect the keyboard Rear of the PC UnitBurglarproof lock Expansion card slotsSerial connector Parallel connectorCRT connector Line in terminalInternal hard disk drive Power supply unitInside the PC Unit Secondary IDE connector IDE2 Floppy disk drive connector FDD Primary IDE connector IDE1Internal battery MotherboardInstallation Connection Installation Location of InstallationVertical Placement Mounting FeetPage Example of Installation Point Connection Connecting the Display/Keyboard/Mouse Plugging the power cord into power receptaclePlugging the power cord into inlet of display unit Connecting the mouseConnecting the keyboard Connecting the display cable to the PC unitConnect the Power Cord Page Power On How to Power On Setting Up ConsiderationsSetting Up Windows XP Turn on the PCClick Next Click IgnoreSetting Up Windows Point Click PerformClick OK. The PC restarts Turn on the computerClick Standard setting and Next Click User for this computer... and NextSelect Restart and click OK Problem During Setup? For Windows XP How to Turn OffTurn Off the Computer For Windows For Windows MeHardware Keyboard Caps Lock key Ctrl keyWindows key Alt keyCDs Guidelines for CD MediaInserting or Removing a CD Inserting a CDPress the CD eject button Pull the tray out with a handRemoving the CD Manually push the tray until it clicksInserting a Floppy Disk Floppy DisksInserting or Removing a Floppy Disk Point Make sure that the floppy disk access lamp is off Removing a Floppy DiskHard Disk Maintenance of the Hardware Maintenance of the PC UnitMaintenance of the Mouse Remove the ball and clean it with waterMaintenance of the Keyboard Cleaning CDsCleaning the Floppy Disk Drive Clean the inside of the mouseSystem Expansion Before Installing a Peripheral Device Use an appropriate screwdriver Remove the two screws on the PC unit Remove the upper cover Removing the CoverRemoving the Cover Installing Memory Modules Location of Memory Modules Applicable Memory Modules Memory Module CombinationsInstalling Memory Modules Point Installing an Expansion Card Unplug the PC Remove the upper cover Installing an Expansion CardLocation of expansion Cards Applicable Expansion Cards Remove the expansion card mounting bracket Remove the slot coverInstall the expansion card mounting bracket Reinstall the upper coverInsert the expansion card into the slot Plug the PC Turn on the PCTechnical Information List of Specifications PC SpecificationsCPU LAN function CSMA/CDConnector Specifications CRT connectorLAN connector 100BASE-TX/10BASE-T Parallel connectorKeyboard Connector Serial connectorMouse connector Symbol Glossary
Related manuals
Manual 82 pages 52.81 Kb
Top Page Image Contents