Fujitsu M3093DE/DG manual Fujitsu Australia Limited

Page 4

Please send your comments on this manual or on Fujitsu products to the following addresses:

FUJITSU COMPUTER PRODUCTS OF	FUJITSU FRANCE S.A.
AMERICA,INC.	Bâtiment Aristote,17 rue Olof palme
2904 Orchard Parkway,San Jose.	94006 Créteil cedex,FRANCE
California 95134-2022,U.S.A.	TEL:33-14-513-1616
TEL:1-408-432-6333	FAX:33-14-399-0700
FAX:1-408-432-3908
Home page:http://www.fcpa.com/	FUJITSU HONG KONG Limited
	Room 2521,Sum Hung Kai Centre
FUJITSU AUSTRALIA LIMITED	30 Harbour Road Wanchal,Hong Kong
475 Victoria Avenue Chatswood.	TEL:852-827-5780
N.S.W2067,AUSTRALIA	FAX:852-827-4724
TEL:61-2-410-4555	TLX:62667
FAX:61-2-411-8603
	FUJITSU ITALIA S.p.A.
FUJITSU CANADA,INC.	Via Melchiorre Gioia,No.8-20124
2800 Matheson Blvd.East,Mississauga.	Milano,ITALY
Ontario 4X5,CANADA	TEL:39-2-6351
TEL:1-905-602-5454	FAX:39-2-6572257
FAX:1-905-602-5457
	FUJITSU NORDIC AB
FUJITSU DEUTSCHLAND GmbH.	Kung Hans vag,S-19176
Frankfurter Ring 211,	Sollentuna,SWEDEN
8000 München 40,F.R,GERMANY	TEL:46-8-626-6000
TEL:49-89-32378-0	FAX:46-8-626-6711
FAX:49-89-32378-100
	FUJITSU LIMITED
FUJITSU ESPAÑA,S.A	International Operations
Edificio torre Europa 5a	Marunouchi 1-6-1, Chiyoda-ku,Tokyo 100
Paseo de la Castellana 95 Madrid 28046,SPAIN	JAPAN
TEL:34-1-581-8400	TEL:(81-3)3216-3211
FAX:34-1-581-8125	FAX:(81-3)3213-7174
	TLX:J2283
FUJITSU EUROPE LTD.	Cable:”FUJITSU LIMITED TOKYO”
2,Longwalk Road,Stockey Park,Uxbridge	Home page:http://www.fujitsu.co.jp/
Middlesex,UB11 1AB,U.K
TEL:44-81-573-4444
FAX:44-81-573-2643
Home page:http://www.fujitsu-europe.com/

Image 4

Contents M3093DE/DG Image Scanner Page Page Fujitsu Australia Limited Important Note to Users Preface Conventions Page Contents Page Description Operating Instruction Page Description Units No. Function Guide a AssembliesRetaining Thumb screw Spring Consumables Bearing Power Read Check IndicatorsPower Page Operating Instruction Loading Document on the ADF Lift up the ADF lever to openSet the paper select lever as Follows Close the ADFPull up the ADF paper chute until It clicksDocument on the ADF paper Fan the sheets before settingChute Angle the document edges as follows Documents Guide lever Both sides Loading Document on the Flatbed Loading Document Larger than the Document Board Reading a Page from a Thick Book Page Cleaning Cleaning Supplies and Cleaning Area SuppliesCleaning area FlatbedCleaning the ADF Lift up the ADF lever to open the ADF Remove dirt and dust as followsPick roller Sheet guide white part Wipe the sheet guide Cleaner F2 Surface with clean and dryMoisten a cotton swab with Wipe the Plastic rollerCleaning the Flatbed Apply Cleaner F1 to a clean clothWipe the document holding pad Allow to dryReplacement of Parts Pad ASY or Pad Slide the paper selectLever to N Slide the pad ASY to the leftUntil it clicks in the reverse Attach the pad ASY to the ADFSequence of step Pick Roller Lift up the ADF lever to open Remove the two thumb screwsSlide the pick roller to the retaining Spring side until the axisOpposite side is disengaged Lift and remove itAttach the retaining spring to a New rollerSequence of and align Attach the Guide a in the reverseScrew hole Tighten the thumb screws Close the ADF unit Page Troubleshooting Paper JAM Remove the documents fromADF paper chute Close the ADF until the ADF leverConnect the power cable correctly Press the power switch Contact manufacturer’s authorized service centerInitial Checks Are the documents loaded on the ADF Is the baud rate System 4800 bps? Default is 4800 bps Is halftone or dithering processing selected? Select a Line Art mode from Select the Photo mode White level following offClean the dirty parts Host computerIs the surface of the ADF Check Clean the pick roller Clean or replace the Pad ASYFlatten the curl or use Flatbed to read the documentDo not mix different width documents Symptom8 Paper double feed occurs frequently Is the height of document less than 0.16 4mm? Flatten the curl or use the flatbed to read the document Install it correctly See p4-2Set the select lever to T. See p2-3 Clean the pick roller. See p3-4, p3-6 Replace the pick roller. See p4-4YES Test Mode for Maintenance LED status on error Problem Checklist General