Cisco Systems 6500-E, WS-C6513-E-RF manual Press down

Page 13

Installing and Removing the Module

Figure 6

Clearing the EMI Gasket in a Horizontal Slot Chassis

 

WS-X6K-SUP2-2GE

 

1

 

CONSOLE

 

 

 

 

PORT

 

CONSOLE

MODE

 

SUPERVISOR2

 

 

WS-X6K-SUP2-2GE

 

2

 

CONSOLE

 

 

 

 

PORT

 

CONSOLE

MODE

 

SUPERVISOR2

 

3

 

 

Press down

 

4

 

 

FAN

WS-X6224

 

STATUS

 

 

5

 

 

 

24 PORT 100FX

 

6

 

Switch

Load

 

 

100%

 

 

 

 

PORT 1

PORT 2

PCMCIA

EJECT

 

 

 

1%

 

 

 

Switch

Load

 

 

100%

 

 

 

 

PORT 1

PORT 2

PCMCIA

EJECT

 

 

 

1%

 

 

Press down

SELECT

NEXT

3

4 4

 

WS-C6500-SFM

5

5

 

 

SWITCH

 

FABIRD MDL

6

6

 

S

 

TU

E

TA

TIV

S

AC

1 mm Gap between the module EMI gasket and the module above it

58570

b.Using the thumb and forefinger of each hand, grasp the two ejector levers and press down to create a small (0.040 inch [1 mm]) gap between the EMI gasket and the module above it. (See Figure 6.)

Caution Pressing down too firmly on the levers will bend and damage them.

c.While pressing down, simultaneously close the left and right ejector levers to fully seat the module in the backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure 7.)

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

13

Image 13
Contents Product Number WS-SVC-CMM Front Panel Descriptions ContentsDescription ColorColor Description Port T1 and E1 Port AdaptersShows the front panel of the 24-port FXS port adapter Port FXS Port AdapterAd-Hoc Conferencing and Transcoding Port Adapter RequirementsHardware Requirements Safety OverviewSoftware Requirements Safety Overview Safety Overview Installing the Module Installing and Removing the ModuleRequired Tools Horizontal slots Positioning the Module in a Horizontal Slot Chassis Press down Ejector Lever Closure in a Horizontal Slot Chassis Vertical slotsPositioning the Module in a Vertical Slot Chassis Press left Ejector Lever Closure in a Vertical Slot Chassis Removing the ModuleHorizontal slots Removing a Port Adapter from Module Slots 1 through Removing and Replacing Port AdaptersModule Bottom View Module Top View with Port Adapters Installed Installing a Port Adapter in Module Slots 1 through Removing and Replacing Port Adapters Removing and Replacing Port Adapters RJ-45 Port Connector and Cabling Specifications Verifying the InstallationReceive R1 Receive T1 Not connected Transmit R Transmit T Pin1 DescriptionRJ-21 Telco Interface 90-Degree Cable Connector RJ-21 Port Connector and Cabling SpecificationsPort Connector Pin Number Signal Accessing the Port Adapter PortsConfiguring the Port Adapter Clock Source Configuring the Port Adapter PortsSlot0ws-svc-cmm Disaster Recovery for Module Software UpgradesDisaster Recovery for Module Software Upgrades Password Recovery Related Documentation Regulatory Standards Compliance

6513-E, 6500-E, WS-C6513-E-RF specifications

Cisco Systems is renowned for its networking and telecommunications equipment, and its Catalyst 6500-E series, including models like the 6513-E and WS-C6513-E-RF, exemplifies cutting-edge technology in enterprise networking. The Catalyst 6500-E series switches are versatile, high-performance devices designed to meet the demands of large enterprises and data centers.

The Cisco Catalyst 6513-E switch is a modular chassis that supports a variety of interface modules and line cards, allowing sleek customization and scalability to accommodate growing networks. The 6513-E features a 13-slot architecture, allowing for up to 11 modules, plus a dedicated supervisor engine for enhanced performance and reliability. This switch can support a mix of Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces, providing great flexibility depending on network requirements.

One of the hallmark technologies of the 6500-E series is Cisco's Virtual Switching System (VSS), which enables two physical switches to operate as a single logical switch. This feature significantly enhances redundancy and improves manageability by allowing network administrators to treat multiple devices as one. The series supports sophisticated features such as Cisco's Enhanced Quality of Service (QoS) capabilities, which enable fine-tuned traffic management to prioritize critical applications and ensure optimal performance throughout the network.

Security is a paramount concern for enterprise environments, and the 6500-E series incorporates robust security features through Cisco's TrustSec technology. This function allows for the creation of secure segments within the network, improving protection against potential threats. Additionally, the switches support advanced authentication features like 802.1X, enabling secure device access.

The WS-C6513-E-RF model, which stands for “Refurbished,” offers an economical option without sacrificing the performance and reliability inherent in the series. These switches are particularly appealing to budget-conscious organizations that still need the advanced features of Cisco products.

Overall, the Cisco Systems Catalyst 6500-E series is a cornerstone for enterprise networking. With its modular design, VSS capabilities, advanced QoS features, and comprehensive security measures, it remains an ideal solution for organizations looking to build a scalable and secure network infrastructure. Its versatility through the WS-C6513-E-RF variant allows businesses of all sizes to leverage high-performance networking without a heavy financial burden. As networking demands evolve, the Catalyst 6500-E series continues to be a key player in delivering reliable and efficient networking solutions.