Cisco Systems 6513-E, 6500-E Vertical slots, Ejector Lever Closure in a Horizontal Slot Chassis

Page 14

Installing and Removing the Module

Figure 7

Ejector Lever Closure in a Horizontal Slot Chassis

FAN STATUS

1

2

3

4

5

6

WS-X6K-SUP2-2GE

SUPERVISOR2

WS-X6K-SUP2-2GE

SUPERVISOR2

WS-C6500-SFM

SWITCH FABRIC MDL

 

 

Switch

Load

 

 

CONSOLE

100%

 

 

 

 

PORT 1

 

 

PORT

 

PORT 2

CONSOLE

MODE

 

 

 

PCMCIA

 

 

 

 

EJECT

 

 

 

 

1%

 

 

 

 

Switch

Load

 

 

CONSOLE

100%

 

 

 

 

PORT 1

 

 

PORT

 

PORT 2

CONSOLE

MODE

 

 

 

 

PCMCIA

EJECT

 

 

 

 

1%

 

 

SELECT

NEXT

58571

Ejector levers flush with module faceplate

Note Failure to fully seat the module in the backplane connector can result in error messages.

d.Tighten the two captive installation screws on the module.

Note Make sure that the ejector levers are fully closed before tightening the captive installation screws.

Vertical slots

a.Position the module in the slot. (See Figure 8.) Make sure that you align the sides of the module carrier with the slot guides on the top and bottom of the slot.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

14

Image 14
Contents Product Number WS-SVC-CMM Contents Front Panel DescriptionsColor DescriptionPort T1 and E1 Port Adapters Color DescriptionPort FXS Port Adapter Shows the front panel of the 24-port FXS port adapterRequirements Ad-Hoc Conferencing and Transcoding Port AdapterSoftware Requirements Safety OverviewHardware Requirements Safety Overview Safety Overview Required Tools Installing and Removing the ModuleInstalling the Module Horizontal slots Positioning the Module in a Horizontal Slot Chassis Press down Vertical slots Ejector Lever Closure in a Horizontal Slot ChassisPositioning the Module in a Vertical Slot Chassis Press left Removing the Module Ejector Lever Closure in a Vertical Slot ChassisHorizontal slots Removing and Replacing Port Adapters Removing a Port Adapter from Module Slots 1 throughModule Bottom View Module Top View with Port Adapters Installed Installing a Port Adapter in Module Slots 1 through Removing and Replacing Port Adapters Removing and Replacing Port Adapters Verifying the Installation RJ-45 Port Connector and Cabling SpecificationsPin1 Description Receive R1 Receive T1 Not connected Transmit R Transmit TRJ-21 Port Connector and Cabling Specifications RJ-21 Telco Interface 90-Degree Cable ConnectorAccessing the Port Adapter Ports Port Connector Pin Number SignalConfiguring the Port Adapter Ports Configuring the Port Adapter Clock SourceDisaster Recovery for Module Software Upgrades Slot0ws-svc-cmmDisaster Recovery for Module Software Upgrades Password Recovery Regulatory Standards Compliance Related Documentation

6513-E, 6500-E, WS-C6513-E-RF specifications

Cisco Systems is renowned for its networking and telecommunications equipment, and its Catalyst 6500-E series, including models like the 6513-E and WS-C6513-E-RF, exemplifies cutting-edge technology in enterprise networking. The Catalyst 6500-E series switches are versatile, high-performance devices designed to meet the demands of large enterprises and data centers.

The Cisco Catalyst 6513-E switch is a modular chassis that supports a variety of interface modules and line cards, allowing sleek customization and scalability to accommodate growing networks. The 6513-E features a 13-slot architecture, allowing for up to 11 modules, plus a dedicated supervisor engine for enhanced performance and reliability. This switch can support a mix of Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces, providing great flexibility depending on network requirements.

One of the hallmark technologies of the 6500-E series is Cisco's Virtual Switching System (VSS), which enables two physical switches to operate as a single logical switch. This feature significantly enhances redundancy and improves manageability by allowing network administrators to treat multiple devices as one. The series supports sophisticated features such as Cisco's Enhanced Quality of Service (QoS) capabilities, which enable fine-tuned traffic management to prioritize critical applications and ensure optimal performance throughout the network.

Security is a paramount concern for enterprise environments, and the 6500-E series incorporates robust security features through Cisco's TrustSec technology. This function allows for the creation of secure segments within the network, improving protection against potential threats. Additionally, the switches support advanced authentication features like 802.1X, enabling secure device access.

The WS-C6513-E-RF model, which stands for “Refurbished,” offers an economical option without sacrificing the performance and reliability inherent in the series. These switches are particularly appealing to budget-conscious organizations that still need the advanced features of Cisco products.

Overall, the Cisco Systems Catalyst 6500-E series is a cornerstone for enterprise networking. With its modular design, VSS capabilities, advanced QoS features, and comprehensive security measures, it remains an ideal solution for organizations looking to build a scalable and secure network infrastructure. Its versatility through the WS-C6513-E-RF variant allows businesses of all sizes to leverage high-performance networking without a heavy financial burden. As networking demands evolve, the Catalyst 6500-E series continues to be a key player in delivering reliable and efficient networking solutions.