Cisco Systems 6500-E Verifying the Installation, RJ-45 Port Connector and Cabling Specifications

Page 25

Verifying the Installation

Caution Using the screws or standoffs to seat the port adapter could warp the port adapter. Before you install and tighten the securing screws, ensure that the port adapter is fully seated by visually verifying that the bottom of the port adapter is in contact with the top of the mounting posts.

Step 6 Install the two standoffs and two Phillips screws to secure the port adapter. (See Figure 12.)

Step 7 Install the module into the Catalyst 6500 series switch or Cisco 7600 series router; see the “Installing the Module” section on page 10.

Verifying the Installation

Enter the show module mod-numcommand to verify that the system acknowledges the new module and has brought it online.

This example shows the output of the show module command with a module in slot 4:

Console>

(enable) show module 4

 

 

 

Mod

Slot

Ports Module-Type

Model

 

Sub Status

---

----

-----

-------------------------

-------------------

--- --------

4

4

5

Communication Media Mod.

WS-SVC-CMM

no ok

Mod

Module-Name

 

Serial-Num

 

 

 

---

--------------------

-----------

 

 

 

4

 

 

 

sad054206jc

 

 

 

Mod

MAC-Address(es)

 

Hw

Fw

Sw

---

-------------------------------------- ------

----------

-----------------

4

00-01-64-46-6a-0e to

00-01-64-46-6a-17 1.0

12.2(2002012.2(20020530:100440

RJ-45 Port Connector and Cabling Specifications

Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036

Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

25

Image 25
Contents Product Number WS-SVC-CMM Front Panel Descriptions ContentsDescription ColorColor Description Port T1 and E1 Port AdaptersShows the front panel of the 24-port FXS port adapter Port FXS Port AdapterAd-Hoc Conferencing and Transcoding Port Adapter RequirementsHardware Requirements Safety OverviewSoftware Requirements Safety Overview Safety Overview Installing the Module Installing and Removing the ModuleRequired Tools Horizontal slots Positioning the Module in a Horizontal Slot Chassis Press down Ejector Lever Closure in a Horizontal Slot Chassis Vertical slotsPositioning the Module in a Vertical Slot Chassis Press left Ejector Lever Closure in a Vertical Slot Chassis Removing the ModuleHorizontal slots Removing a Port Adapter from Module Slots 1 through Removing and Replacing Port AdaptersModule Bottom View Module Top View with Port Adapters Installed Installing a Port Adapter in Module Slots 1 through Removing and Replacing Port Adapters Removing and Replacing Port Adapters RJ-45 Port Connector and Cabling Specifications Verifying the InstallationReceive R1 Receive T1 Not connected Transmit R Transmit T Pin1 DescriptionRJ-21 Telco Interface 90-Degree Cable Connector RJ-21 Port Connector and Cabling SpecificationsPort Connector Pin Number Signal Accessing the Port Adapter PortsConfiguring the Port Adapter Clock Source Configuring the Port Adapter PortsSlot0ws-svc-cmm Disaster Recovery for Module Software UpgradesDisaster Recovery for Module Software Upgrades Password Recovery Related Documentation Regulatory Standards Compliance

6513-E, 6500-E, WS-C6513-E-RF specifications

Cisco Systems is renowned for its networking and telecommunications equipment, and its Catalyst 6500-E series, including models like the 6513-E and WS-C6513-E-RF, exemplifies cutting-edge technology in enterprise networking. The Catalyst 6500-E series switches are versatile, high-performance devices designed to meet the demands of large enterprises and data centers.

The Cisco Catalyst 6513-E switch is a modular chassis that supports a variety of interface modules and line cards, allowing sleek customization and scalability to accommodate growing networks. The 6513-E features a 13-slot architecture, allowing for up to 11 modules, plus a dedicated supervisor engine for enhanced performance and reliability. This switch can support a mix of Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces, providing great flexibility depending on network requirements.

One of the hallmark technologies of the 6500-E series is Cisco's Virtual Switching System (VSS), which enables two physical switches to operate as a single logical switch. This feature significantly enhances redundancy and improves manageability by allowing network administrators to treat multiple devices as one. The series supports sophisticated features such as Cisco's Enhanced Quality of Service (QoS) capabilities, which enable fine-tuned traffic management to prioritize critical applications and ensure optimal performance throughout the network.

Security is a paramount concern for enterprise environments, and the 6500-E series incorporates robust security features through Cisco's TrustSec technology. This function allows for the creation of secure segments within the network, improving protection against potential threats. Additionally, the switches support advanced authentication features like 802.1X, enabling secure device access.

The WS-C6513-E-RF model, which stands for “Refurbished,” offers an economical option without sacrificing the performance and reliability inherent in the series. These switches are particularly appealing to budget-conscious organizations that still need the advanced features of Cisco products.

Overall, the Cisco Systems Catalyst 6500-E series is a cornerstone for enterprise networking. With its modular design, VSS capabilities, advanced QoS features, and comprehensive security measures, it remains an ideal solution for organizations looking to build a scalable and secure network infrastructure. Its versatility through the WS-C6513-E-RF variant allows businesses of all sizes to leverage high-performance networking without a heavy financial burden. As networking demands evolve, the Catalyst 6500-E series continues to be a key player in delivering reliable and efficient networking solutions.