Cisco Systems WS-C6513-E-RF, 6500-E manual Removing and Replacing Port Adapters

Page 24

Removing and Replacing Port Adapters

Step 4 In Figure 13, note the location of the two slot 4 standoff mounting posts. Remove the two mounting posts that secure the port adapter.

Step 5 In Figure 13, note the location of the two slot 4 connectors. Carefully remove the port adapter, taking care when lifting up and disconnecting the port adapter from the connectors.

Tip To unseat the port adapter from the two connectors, grasp the left-hand side of the port adapter with one hand, and gently but firmly pull up on the port adapter until it is free of the connectors.

Step 6 Place the removed port adapter in an antistatic bag.

Step 7 Install the module into the Catalyst 6500 series switch or the Cisco 7600 series router; see the “Installing the Module” section on page 10.

Installing an Ad-Hoc Conferencing and Transcoding Port Adapter in Slot 4

To install a port adapter in module slot 4, perform these steps:

Note To install a port adapter in module slot 4, you need to remove the face plate from the port adapter. To remove the face plate, position the port adapter with the face plate facing toward you, turn the port adapter component side down on an antistatic mat or foam pad, and then remove the two Phillips screws that secure the face plate.

Step 1 Remove the module from the Catalyst 6500 series switch or the Cisco 7600 series router; see the “Removing the Module” section on page 17.

Step 2 Carefully place the module, component side up, on an antistatic mat or foam pad with the front of the module facing toward you.

Step 3 In Figure 13, note the location of the two, slot 4 Phillips screw mounting posts, and note the location of the two, slot 4 standoff mounting posts.

Step 4 Align the port adapter with the two slot 4 Phillips screw mounting posts and two slot 4 standoff mounting posts. Ensure that the connectors on the port adapter are aligned with the connectors on the module.

Step 5 When all mounting posts and mounting holes are aligned, gently push down on the port adapter edges that ensure that the keys on the connectors are properly aligned. If necessary, while applying pressure with your left hand, rock the module up and down slightly with your right hand to seat the port adapter.

Tip To seat the port adapter into the two connectors, grasp the left-hand side of the port adapter with one hand, and gently but firmly push down on the left-hand side of the port adapter until it is seated in the connectors. You will hear a distinctive “click” when the port adapter seats in the connectors.

Caution Use care not to damage the connectors on the port adapter. If you damage a connector, you will have to return the port adapter to Cisco for repair.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Product Number WS-SVC-CMM Contents Front Panel DescriptionsColor DescriptionPort T1 and E1 Port Adapters Color DescriptionPort FXS Port Adapter Shows the front panel of the 24-port FXS port adapterRequirements Ad-Hoc Conferencing and Transcoding Port AdapterSafety Overview Hardware RequirementsSoftware Requirements Safety Overview Safety Overview Installing and Removing the Module Installing the ModuleRequired Tools Horizontal slots Positioning the Module in a Horizontal Slot Chassis Press down Vertical slots Ejector Lever Closure in a Horizontal Slot ChassisPositioning the Module in a Vertical Slot Chassis Press left Removing the Module Ejector Lever Closure in a Vertical Slot ChassisHorizontal slots Removing and Replacing Port Adapters Removing a Port Adapter from Module Slots 1 throughModule Bottom View Module Top View with Port Adapters Installed Installing a Port Adapter in Module Slots 1 through Removing and Replacing Port Adapters Removing and Replacing Port Adapters Verifying the Installation RJ-45 Port Connector and Cabling SpecificationsPin1 Description Receive R1 Receive T1 Not connected Transmit R Transmit TRJ-21 Port Connector and Cabling Specifications RJ-21 Telco Interface 90-Degree Cable ConnectorAccessing the Port Adapter Ports Port Connector Pin Number SignalConfiguring the Port Adapter Ports Configuring the Port Adapter Clock SourceDisaster Recovery for Module Software Upgrades Slot0ws-svc-cmmDisaster Recovery for Module Software Upgrades Password Recovery Regulatory Standards Compliance Related Documentation

6513-E, 6500-E, WS-C6513-E-RF specifications

Cisco Systems is renowned for its networking and telecommunications equipment, and its Catalyst 6500-E series, including models like the 6513-E and WS-C6513-E-RF, exemplifies cutting-edge technology in enterprise networking. The Catalyst 6500-E series switches are versatile, high-performance devices designed to meet the demands of large enterprises and data centers.

The Cisco Catalyst 6513-E switch is a modular chassis that supports a variety of interface modules and line cards, allowing sleek customization and scalability to accommodate growing networks. The 6513-E features a 13-slot architecture, allowing for up to 11 modules, plus a dedicated supervisor engine for enhanced performance and reliability. This switch can support a mix of Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces, providing great flexibility depending on network requirements.

One of the hallmark technologies of the 6500-E series is Cisco's Virtual Switching System (VSS), which enables two physical switches to operate as a single logical switch. This feature significantly enhances redundancy and improves manageability by allowing network administrators to treat multiple devices as one. The series supports sophisticated features such as Cisco's Enhanced Quality of Service (QoS) capabilities, which enable fine-tuned traffic management to prioritize critical applications and ensure optimal performance throughout the network.

Security is a paramount concern for enterprise environments, and the 6500-E series incorporates robust security features through Cisco's TrustSec technology. This function allows for the creation of secure segments within the network, improving protection against potential threats. Additionally, the switches support advanced authentication features like 802.1X, enabling secure device access.

The WS-C6513-E-RF model, which stands for “Refurbished,” offers an economical option without sacrificing the performance and reliability inherent in the series. These switches are particularly appealing to budget-conscious organizations that still need the advanced features of Cisco products.

Overall, the Cisco Systems Catalyst 6500-E series is a cornerstone for enterprise networking. With its modular design, VSS capabilities, advanced QoS features, and comprehensive security measures, it remains an ideal solution for organizations looking to build a scalable and secure network infrastructure. Its versatility through the WS-C6513-E-RF variant allows businesses of all sizes to leverage high-performance networking without a heavy financial burden. As networking demands evolve, the Catalyst 6500-E series continues to be a key player in delivering reliable and efficient networking solutions.
Top Page Image Contents