Cisco Systems 6513-E manual Removing the Module, Ejector Lever Closure in a Vertical Slot Chassis

Page 17

Installing and Removing the Module

Figure 10

Ejector Lever Closure in a Vertical Slot Chassis

FAN

STATUS

24PORT100FX

WS-X6224

STATUS

ACTIVE

NE

SE

XT

LE

 

CT

All ejector levers flush with module faceplate

SU PE RV ISO R2

ST

 

ATU

S

S

YST

CO

EM

NS

P

OLE

WR

 

MG

RESET

 

MT

CON

 

SO

 

LE

 

CO

 

MODE PORT NSOLE

 

PC

 

MC

 

IA

 

EJE

 

CT

 

1%

100 % S

 

wit

 

ch

 

Lo

 

ad

 

POR

 

T1

 

POR

 

T2

WS -X 6K -S UP

2 2G- E

SUPERVISOR2

ST

 

ATU

S

S

YST

CO

EM

NS

P OLE

WR

RE

MG

MT

SET

CONSOLE

 

MODE PORT CONSOLE

 

PCMCIA

 

EJECT

 

1%

100%

 

Switch

 

Load

 

PORT1

 

PORT2

WS-X6K -SUP2 -2GE

63587

e.Tighten the two captive installation screws on the module.

Note Make sure that the ejector levers are fully closed before tightening the captive installation screws.

This completes the module installation procedure.

Removing the Module

This section describes how to remove the module from a Catalyst 6500 series switch or the Cisco 7600 series router.

Caution During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.

Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

17

Image 17
Contents Product Number WS-SVC-CMM Front Panel Descriptions ContentsDescription ColorColor Description Port T1 and E1 Port AdaptersShows the front panel of the 24-port FXS port adapter Port FXS Port AdapterAd-Hoc Conferencing and Transcoding Port Adapter RequirementsSoftware Requirements Safety OverviewHardware Requirements Safety Overview Safety Overview Required Tools Installing and Removing the ModuleInstalling the Module Horizontal slots Positioning the Module in a Horizontal Slot Chassis Press down Ejector Lever Closure in a Horizontal Slot Chassis Vertical slotsPositioning the Module in a Vertical Slot Chassis Press left Ejector Lever Closure in a Vertical Slot Chassis Removing the ModuleHorizontal slots Removing a Port Adapter from Module Slots 1 through Removing and Replacing Port AdaptersModule Bottom View Module Top View with Port Adapters Installed Installing a Port Adapter in Module Slots 1 through Removing and Replacing Port Adapters Removing and Replacing Port Adapters RJ-45 Port Connector and Cabling Specifications Verifying the InstallationReceive R1 Receive T1 Not connected Transmit R Transmit T Pin1 DescriptionRJ-21 Telco Interface 90-Degree Cable Connector RJ-21 Port Connector and Cabling SpecificationsPort Connector Pin Number Signal Accessing the Port Adapter PortsConfiguring the Port Adapter Clock Source Configuring the Port Adapter PortsSlot0ws-svc-cmm Disaster Recovery for Module Software UpgradesDisaster Recovery for Module Software Upgrades Password Recovery Related Documentation Regulatory Standards Compliance

6513-E, 6500-E, WS-C6513-E-RF specifications

Cisco Systems is renowned for its networking and telecommunications equipment, and its Catalyst 6500-E series, including models like the 6513-E and WS-C6513-E-RF, exemplifies cutting-edge technology in enterprise networking. The Catalyst 6500-E series switches are versatile, high-performance devices designed to meet the demands of large enterprises and data centers.

The Cisco Catalyst 6513-E switch is a modular chassis that supports a variety of interface modules and line cards, allowing sleek customization and scalability to accommodate growing networks. The 6513-E features a 13-slot architecture, allowing for up to 11 modules, plus a dedicated supervisor engine for enhanced performance and reliability. This switch can support a mix of Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces, providing great flexibility depending on network requirements.

One of the hallmark technologies of the 6500-E series is Cisco's Virtual Switching System (VSS), which enables two physical switches to operate as a single logical switch. This feature significantly enhances redundancy and improves manageability by allowing network administrators to treat multiple devices as one. The series supports sophisticated features such as Cisco's Enhanced Quality of Service (QoS) capabilities, which enable fine-tuned traffic management to prioritize critical applications and ensure optimal performance throughout the network.

Security is a paramount concern for enterprise environments, and the 6500-E series incorporates robust security features through Cisco's TrustSec technology. This function allows for the creation of secure segments within the network, improving protection against potential threats. Additionally, the switches support advanced authentication features like 802.1X, enabling secure device access.

The WS-C6513-E-RF model, which stands for “Refurbished,” offers an economical option without sacrificing the performance and reliability inherent in the series. These switches are particularly appealing to budget-conscious organizations that still need the advanced features of Cisco products.

Overall, the Cisco Systems Catalyst 6500-E series is a cornerstone for enterprise networking. With its modular design, VSS capabilities, advanced QoS features, and comprehensive security measures, it remains an ideal solution for organizations looking to build a scalable and secure network infrastructure. Its versatility through the WS-C6513-E-RF variant allows businesses of all sizes to leverage high-performance networking without a heavy financial burden. As networking demands evolve, the Catalyst 6500-E series continues to be a key player in delivering reliable and efficient networking solutions.