Cisco Systems Cisco SFS 7000P manual Power and Fan Modules, Locating the Power Supply or Fan Unit

Page 48

C H A P T E R 3

Installing Field Replaceable Units

This chapter describes how to install the following field replaceable units (FRUs) in the Cisco SFS 7000P switch:

•Power and Fan Modules, page 3-1

•Installing a Power Supply or Fan Unit, page 3-2

•Removing Power Supplies and Fan Units, page 3-5

Power and Fan Modules

The Cisco SFS 7000P power supplies and fan units are hot-swappable. You can add a second module without powering off the switch. If you have two power or fan units installed, you can remove one of them without removing power from the switch.

Locating the Power Supply or Fan Unit

Each power supply and fan unit is a single module. Both power or fan units are located on the front of the switch. When facing the front of the switch, the power modules are located in the left and right slots of the Cisco SFS 7000P switch.

		Cisco SFS 7000P Hardware Installation Guide
		Cisco SFS 7000P Hardware Installation Guide
	OL-9167-01 Rev. A0			3-1
	OL-9167-01 Rev. A0			3-1

Image 48

Contents Cisco SFS 7000P Hardware Installation Guide Page Page Page N T E N T S Latency Managing the System ViiDisplaying Hardware Errors ViiiPreface AudienceOrganization ConventionsChapter Title Description Convention DescriptionItalic screen font Boldface screen fontStatement 1071-Warning Definition Varoitus Tärkeitä TurvallisuusohjeitaXii Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaXiii Aviso Instruções Importantes DE Segurança XivVarning! Viktiga Säkerhetsanvisningar Spara Dessa AnvisningarRelated Documentation XviObtaining Documentation Cisco.comProduct Documentation DVD XviiDocumentation Feedback Cisco Product Security OverviewOrdering Documentation XviiiReporting Security Problems in Cisco Products XixObtaining Technical Assistance Cisco Technical Support & Documentation WebsiteSubmitting a Service Request Definitions of Service Request SeverityXxi Obtaining Additional Publications and Information XxiiXxiii Xxiv Switch Description Product OverviewSwitch Components ConnectorsPower Supplies and Fan Units LEDsSystem Features InfiniBand ConnectivityScalability High AvailabilityHardware Administrative Features Diagnostics Installing the Cisco SFS 7000P Switch Safety Preparing for Installation Configuring Basic ConnectivityAttaching a Serial Console Cable to a PC or Terminal Powering Up the Chassis Power Connector LocationsRack-Mounting the Cisco SFS 7000P Switch RequirementsRack-Mounting the Switch Installing the Switch with One PersonAssembled Rack Brackets Holding Bracket Against Inside of Rack Secure Rail Bracket to Rack with Screws Sliding the Switch Into the Rack Connecting Network Devices Installing the Switch with Two PeopleConnecting InfiniBand Devices IB Cable with Pinch Connector 11 Removing a Pinch Connector Connecting Management Devices Managing the SystemInstalling the Cisco SFS 7000P Switch Managing the System Installing the Cisco SFS 7000P Switch Managing the System Power and Fan Modules Locating the Power Supply or Fan UnitInstalling a Power Supply or Fan Unit Failed Power Supplies or Fan UnitsRemoving the Screws from the Power Supply Removing the Power Supply from the Switch Removing Power Supplies and Fan Units Power Supply LEDsOL-9167-01 Rev. A0 OL-9167-01 Rev. A0 LEDs Chassis Status LEDsInfiniBand Port LEDs Color IndicationPower Supply and Fan LEDs Managing the System with Element ManagerUsing the Summary Tab Health Status WindowUsing the Power Supplies Tab Using the Fans TabUsing the Sensors Tab Displaying System InformationDisplaying Power Supply Information SFS-7000P#show power-supplyDisplaying Sensor Information About Diagnostic Tests LED TestsRunning Card Tests Self-TestsRunning a Card Self-Test SFS-7000P#show diagnostic card Running Chassis TestsRunning a Chassis Standard Test SFS-7000Pconfig#diag chassis test standard SFS-7000P-1#show diag postSFS-7000P#show diagnostic fan Running Fan TestsRunning a Self-Test on a Fan SFS-7000P#show diag fru-error SFS-7000P#show diag fanRunning Power Supply Tests Running a LED Test on the Power SupplyRunning a Self-Test on a Power Supply StartEnter the show power-supplycommand SFS-7000P#show diagnostic power-supplyDisplaying Hardware Errors EnableMore sysloghwiflog SFS-7000P#show diagnostic post SFS-7000P#show diagnostic fru-errorError Number Description Power supply I2C communication errorOL-9167-01 Rev. A0 Specification Chassis and Management InterfaceElectrical Specifications Category SpecificationD E IN-1IN-2