Cisco Systems Cisco SFS 7000P Managing the System with Element Manager, Power Supply and Fan LEDs

Page 57

Chapter 4 Managing the Cisco SFS 7000P Switch

Managing the System with Element Manager

Power Supply and Fan LEDs

The power supply and fan unit LEDs are located on the bottom left corner of each power supply or fan unit. For the location of the LEDs, see Figure 4-2. For LED descriptions, see Table 4-3.

The green LED is labeled with a checkmark.

The yellow LED is labeled with an exclamation point (!).

Figure 4-2 Power Supply and Fan LEDs Location

 

154014

!

 

Power Supply/Fan

LEDs

 

Table 4-3

Power Supply and Fan Unit LEDs

Color

Indication

Off

DC output failure.

Green (solid)

AC connected, DC output OK.

Yellow (off)

No failure on the power supply.

Yellow (solid)

Operator intervention required. Failure detected

 

within the power supply.

Managing the System with Element Manager

For information regarding installing the Element Manager, refer to the Cisco SFS 7000 Series Product Family Element Manager User Guide.

 

 

Cisco SFS 7000P Hardware Installation Guide

 

 

 

 

 

 

OL-9167-01 Rev. A0

 

 

4-3

 

 

 

Image 57
Contents Cisco SFS 7000P Hardware Installation Guide Page Page Page N T E N T S Latency Vii Managing the SystemViii Displaying Hardware ErrorsAudience PrefaceConventions OrganizationChapter Title Description Convention DescriptionBoldface screen font Italic screen fontStatement 1071-Warning Definition Varoitus Tärkeitä TurvallisuusohjeitaXii Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaXiii Xiv Aviso Instruções Importantes DE SegurançaSpara Dessa Anvisningar Varning! Viktiga SäkerhetsanvisningarXvi Related DocumentationCisco.com Obtaining DocumentationProduct Documentation DVD XviiCisco Product Security Overview Documentation FeedbackOrdering Documentation XviiiXix Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Obtaining Technical AssistanceSubmitting a Service Request Definitions of Service Request SeverityXxi Xxii Obtaining Additional Publications and InformationXxiii Xxiv Product Overview Switch DescriptionConnectors Switch ComponentsPower Supplies and Fan Units LEDsInfiniBand Connectivity System FeaturesScalability High AvailabilityHardware Administrative Features Diagnostics Installing the Cisco SFS 7000P Switch Safety Preparing for Installation Configuring Basic ConnectivityAttaching a Serial Console Cable to a PC or Terminal Power Connector Locations Powering Up the ChassisRequirements Rack-Mounting the Cisco SFS 7000P SwitchInstalling the Switch with One Person Rack-Mounting the SwitchAssembled Rack Brackets Holding Bracket Against Inside of Rack Secure Rail Bracket to Rack with Screws Sliding the Switch Into the Rack Installing the Switch with Two People Connecting Network DevicesConnecting InfiniBand Devices IB Cable with Pinch Connector 11 Removing a Pinch Connector Managing the System Connecting Management DevicesInstalling the Cisco SFS 7000P Switch Managing the System Installing the Cisco SFS 7000P Switch Managing the System Locating the Power Supply or Fan Unit Power and Fan ModulesFailed Power Supplies or Fan Units Installing a Power Supply or Fan UnitRemoving the Screws from the Power Supply Removing the Power Supply from the Switch Power Supply LEDs Removing Power Supplies and Fan UnitsOL-9167-01 Rev. A0 OL-9167-01 Rev. A0 Chassis Status LEDs LEDsColor Indication InfiniBand Port LEDsManaging the System with Element Manager Power Supply and Fan LEDsHealth Status Window Using the Summary TabUsing the Fans Tab Using the Power Supplies TabDisplaying System Information Using the Sensors TabSFS-7000P#show power-supply Displaying Power Supply InformationDisplaying Sensor Information LED Tests About Diagnostic TestsRunning Card Tests Self-TestsRunning a Card Self-Test SFS-7000P#show diagnostic card Running Chassis TestsRunning a Chassis Standard Test SFS-7000P-1#show diag post SFS-7000Pconfig#diag chassis test standardSFS-7000P#show diagnostic fan Running Fan TestsRunning a Self-Test on a Fan SFS-7000P#show diag fan SFS-7000P#show diag fru-errorRunning a LED Test on the Power Supply Running Power Supply TestsRunning a Self-Test on a Power Supply StartSFS-7000P#show diagnostic power-supply Enter the show power-supplycommandDisplaying Hardware Errors EnableMore sysloghwiflog SFS-7000P#show diagnostic fru-error SFS-7000P#show diagnostic postPower supply I2C communication error Error Number DescriptionOL-9167-01 Rev. A0 Chassis and Management Interface SpecificationCategory Specification Electrical SpecificationsIN-1 D EIN-2