Cisco Systems DSN09EVS720ACK9 manual Supervisor engine for servicing purposes, Disk, Operation

Page 66

Chapter 2 Supervisor Engines

Supervisor Engine 2T

Table 2-20lists Supervisor Engine 2T front panel LEDs and their meanings.

Table 2-24

Supervisor Engine 2T Front Panel Status LEDs

 

 

 

LED

 

Color and Meaning

 

 

 

STATUS

 

The STATUS LED indicates the status of the supervisor engine.

 

 

• Green—All diagnostics pass. The supervisor engine is

 

 

operational (normal initialization sequence).

 

 

• Orange—The supervisor engine is booting or running

 

 

diagnostics (normal initialization sequence) or an

 

 

overtemperature condition has occurred. (A minor temperature

 

 

threshold has been exceeded during environmental

 

 

monitoring.)

 

 

• Red—The diagnostic test failed. The supervisor engine is not

 

 

operational because a fault occurred during the initialization

 

 

sequence or an overtemperature condition has occurred. (A

 

 

major temperature threshold has been exceeded during

 

 

environmental monitoring.)

 

 

 

ID

 

A blue LED that flashes at half-second intervals is used to identify

 

 

the supervisor engine for servicing purposes.

 

 

 

SYSTEM

 

The SYSTEM LED indicates the status of the system components.

 

 

• Green—All chassis environmental monitors are reporting OK.

 

 

• Orange—A minor hardware problem has been detected.

 

 

• Red—A major hardware problem has occurred.

 

 

 

ACTIVE

 

The ACTIVE LED indicates whether the supervisor engine is

 

 

operating in active mode or is in standby mode.

 

 

• Green—The supervisor engine is operational and active.

 

 

• Orange—The supervisor engine is in standby mode.

 

 

 

PWR MGMT

 

The supervisor engine monitors each module’s power requirements

 

 

and status relative to the system’s overall power capacity before

 

 

fully powering up each module in the chassis.

 

 

• Orange—Power-up mode; running self-diagnostics.

 

 

• Green—Power management is functioning normally and

 

 

sufficient power is available for all modules.

 

 

• Orange—A minor power management problem has been

 

 

detected. There is insufficient power for all modules to power

 

 

up.

 

 

• Red—A major power failure has occurred.

 

 

 

DISK 0

 

This LED is illuminated green when the installed Flash PC card is

 

 

being accessed and is performing either a read operation or a write

 

 

operation.

 

 

 

Catalyst 6500 Series Supervisor Engine Guide

2-38

OL-7397-03

 

 

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Catalyst 6500 Series Supervisor Engine Guide Americas HeadquartersCatalyst 6500 Series Supervisor Engine Guide N T E N T S Safety Audience OrganizationChapter Title Description Conventions Convention DescriptionStatement 1071-Warning Definition Bewaar Deze InstructiesWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger Page Xii Obtaining Documentation and Submitting a Service Request Related DocumentationXiv Catalyst 6500 Series Switch Chassis Overview Catalyst 6503 SwitchCatalyst 6503-E Catalyst 6504-E Catalyst Catalyst 6506-E Catalyst Catalyst 6509-E Catalyst 6509-NEB Catalyst 6509-NEB-A Catalyst 6509-V-E Catalyst Catalyst 6513-E Catalyst 6500 Series Switch Chassis Overview Catalyst 6513-E OL-7397-03 Supervisor Engine Supervisor Engine 2 Product Description NumberWS-X6K-S2-PFC2 Feature Description WS-X6K-S2-MSFC2WS-X6K-S2U-MSFC2 SP Dram SP NvramSpecification EnvironmentSystem Color and MeaningStatus ConsoleLink Switch LoadPWR Mgmt PcmciaSupervisor Engine 32 Product Description Number WS-SUP32-GE-3B6lists and describes Supervisor Engine 32 features Supervisor Engine 32 WS-SUP32-10GE-3B Front Panel FeaturesFeature Description LED Button ejects the Pcmcia card from the slotMsfc daughter card version Installed MSFC2AStatus LED indicates the status of the supervisor engine Orange-A minor hardware problem has been detectedRed-A major hardware problem has occurred System LED indicates the status of the system componentsActive Disk 0 Pcmcia LEDSupervisor Engine 32 Pisa WS-S32-GE-PISAWS-S32-10GE-PISA 10lists and describes Supervisor Engine 32 Pisa features PisaFeature Description Pcmcia card from the slot Feature Description Supervisor Engine 32 Pisa Front Panel Status LEDs LED colors indicate the following For Link LEDs associated with the Xenpak uplink ports,Numbers WS-SUP720-3BXL14lists and describes Supervisor Engine 720 features Port Active at one timeWS-SUP720-PFC3A WS-F6K-PFC3A WS-SUP720-3B-PFC3B WS-F6K-PFC3BWS-SUP720-3BXL-PFC3BXL WS-F6K-PFC3BXL 16 Supervisor Engine 720 Front Panel Status LEDs Supervisor Engine 720-10GE Front Panel Features Supervisor Engine 720-10GE18lists and describes Supervisor Engine 720-10GE features Supervisor Engine 720-10GE Features VS-S720-10G-3CXL-PFC3CXL WS-F6K-PFC3CXL MSFC3 WS-F6K-MSFC3Specification Supervisor Engine 720-10GE Front Panel Status LEDs Disk Link Supervisor Engine 2T 22lists and describes Supervisor Engine 2T features Release/notes/ol20679.htmlDram Tsdevicesupporttableslist.htmlFeature Specification Supervisor engine for servicing purposes DiskOperation Link SFP Uplink Link 10GE UplinkOL-7397-03 Installing Supervisor Engines SafetyInstalling a Supervisor Engine Required ToolsInstalling Supervisor Engines Installing a Supervisor Engine Installing Supervisor Engines Installing a Supervisor Engine Chassis with horizontal slots Insert module Between slot guides EMI gasketPress down Chassis with vertical slots Positioning the Module in a Vertical Slot ChassisClearing the EMI Gasket in a Vertical Slot Chassis Installing Supervisor Engines Installing a Supervisor Engine Removing a Supervisor Engine Horizontal slotsCaptive Installation Screw Ejector lever Vertical slots1029 USB Console Port Driver Installation Installing the Cisco Microsoft Windows USB Device DriverInstalling the Cisco Microsoft Windows XP USB Driver Uninstalling the Cisco Microsoft Windows USB Driver Using the Add or Remove Programs utilityUsing the Setup.exe program Installing Pluggable Transceivers Attaching the Network Interface CablesAttaching Optical Network Interface Cables Mode-Conditioning Patch CordTransceiver Mode-Conditioning Patch Cord Usage Xenpak LRM XENPAK-10GB-LRM=X2 LRM RX TX Where to Go Next Connecting Transceivers to a Copper NetworkSFP Supervisor Engine Number of PortsGbic XenpakAppendix a Pluggable Transceivers Console Port Console Port Cables and AdaptersConsole Port Mode Switch Supervisor Engine 2 Only Figure B-1 Identifying a Rollover CableSignal RJ-45 Pin DB-9 Pin RJ-45-to-RJ-45 RJ-45-to-DB-9 Console Rollover CableDevice RTS DTR DSR DCD CTSUplink Ports Console Port Mode 2 Signaling and PinoutsConsole Port Console Device Pin signal Input/Output Supervisor Engine Number Type of Uplink Port Uplink PortsTransceiver Type Cabling Guideline LX4USB Ports Copper and Fiber-Optic ConnectorsRJ-45 Connector CX4Fiber-Optic Connectors SC ConnectorsLC Connectors OL-7397-03 ESD Precautions Attaching Your ESD Grounding StrapCatalyst 6500 Series Supervisor Engine Guide Clip OL-7397-03 D E Network cables installing 3-17uplink ports IN-2Fan tray requirements Reset switch Front panel figure Front panel figure Power requirementFront panel features 2-28front panel LEDs table memory

DSN09EVS720ACK9 specifications

Cisco Systems has long been a leader in networking and technology solutions, and its DSN09EVS720ACK9 model is a prime example of its commitment to delivering high-performance and reliable products. This device is particularly notable for its advanced features, cutting-edge technologies, and robust characteristics, making it an ideal choice for organizations looking to enhance their network infrastructure.

One of the standout features of the Cisco DSN09EVS720ACK9 is its exceptional performance capabilities. The device is equipped with a high-speed processing unit and substantial memory capacity, enabling it to handle a significant number of concurrent connections and data streams. This performance is critical for businesses that rely on efficient data transfer and real-time applications, ensuring seamless operations even under heavy network loads.

Security is a paramount concern for any organization, and the DSN09EVS720ACK9 addresses this need with its integrated security features. The device includes advanced encryption protocols and robust firewall capabilities, safeguarding sensitive data against potential threats. Moreover, it supports security frameworks that enable the implementation of comprehensive access control and threat detection systems, ensuring that only authorized personnel have access to critical network resources.

Additionally, the DSN09EVS720ACK9 is designed to support a variety of networking technologies, including IPv6, which is essential for future-proofing networks as the demand for IP addresses continues to grow. Its compatibility with various protocols and standards ensures seamless integration with existing infrastructure, allowing organizations to leverage their current investments and transition to newer technologies smoothly.

Scalability is another key characteristic of the DSN09EVS720ACK9. Organizations can easily expand their network capabilities using this device without significant disruptions. Whether adding new users, devices, or applications, the DSN09EVS720ACK9 can adapt to changing business needs, making it a flexible solution for both small businesses and large enterprises alike.

In conclusion, the Cisco Systems DSN09EVS720ACK9 is a high-performance networking device that boasts advanced features, robust security, support for multiple networking technologies, and impressive scalability. It stands as a testament to Cisco's innovation and quality in networking solutions, making it an indispensable asset for organizations aiming to enhance their digital infrastructure and drive growth in an increasingly interconnected world.
Top Page Image Contents