Cisco Systems Connecting Cables, Global Site Selector 4490 Back Panel Ports and Receptacles

Page 60

Chapter 3 Installing the Cisco Global Site Selector 4490

Connecting Cables

Connecting Cables

To connect network and console cables to your GSS 4490, follow these steps.

1.For network connections, insert a Category 5 UTP cable into the Ethernet 0 or Ethernet 1 receptacle on the GSS 4490 back panel (Figure 3-9).

2.Connect the other end of the network cable to a hub or switch in your network.

3.For console connections, plug the cable into the console port on the GSS 4490 back panel.

4.Connect the other end of the console cable to a console or a communications server.

Figure 3-9 Global Site Selector 4490 Back Panel Ports and Receptacles

1

97214

2 3 4

1

AC power receptacle

2

Ethernet 0 receptacle

 

 

 

 

3

Ethernet 1 receptacle

4

Console port

 

 

 

 

 

Cisco Global Site Selector 4490 Hardware Installation Guide

3-14

78-15755-01

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Cisco Global Site Selector 4490 Hardware Installation Guide Page Cisco Global Site Selector 4490 Hardware Installation Guide Page N T E N T S Checking Connections Altitude Viii Figure B-1 Page Table A-1 Xii Preface Audience How to Use This Guide Chapter/Appendix DescriptionRelated Documentation Document Title DescriptionSymbols and Conventions XviiBewaar Deze Instructies Varoitus Tärkeitä TurvallisuusohjeitaWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaTA Vare PÅ Disse Instruksjonene Aviso Instruções Importantes DE SegurançaVarning! Viktiga Säkerhetsanvisningar Spara Dessa AnvisningarXxii Introduction IntroductionSystem Hardware Features Cisco Global Site Selector 4490-Front View Hardware Features Front Panel Control ButtonsLED Indicators Front Panel LEDsColor 5shows the location of back panel LEDs, and -3describesInput/Output Ports and Connectors Indicator Color State DescriptionGlobal Site Selector 4490 Back Panel Ports and Receptacles Ethernet Port Pin Number Signal Name RI Ring IndicatorParameters Settings VT100/ANSIChapter Preparing for Installation Safety Warnings Site Requirements Safety GuidelinesSafety Warnings Preparing for Installation Safety Warnings Preparing for Installation Safety Warnings Preparing for Installation Safety Warnings Choosing a Site for Installation Site RequirementsEnsuring Overcurrent Protection Grounding the GSSSafety Guidelines General PrecautionsPreparing for Installation Safety Guidelines Protecting Against Electrostatic Discharge Rack Installation Safety Guidelines Ensuring Proper AirflowStabilizing the System Lifting the SystemPreparing for Installation Safety Guidelines Installing the Cisco Global Site Selector Unpacking and Inspecting the Global Site Selector Tools and Parts Required If the Product is DamagedFour-Post Rack Installation Kit Installing Your Unit Installing the Chassis in a Four-Post Rack Cage nuts Clip nutsRemoving the Inner Slide Rail Attaching the Inner Slide Rail to the GSS Attaching the Slide Rails to the Rack Inserting the Inner Slide Rails Installing the Chassis in a Two-Post Rack Attaching a Bracket to the Right Side of the GSSAttaching the GSS 4490 to the Two-Post Rack Installing the Chassis on a Workbench or Tabletop Connecting Cables Connecting Power Booting the SystemChecking the Front Panel LEDs Color State DescriptionRemoving or Replacing a Cisco Global Site Selector Cisco Global Site Selector 4490 Hardware Installation Guide 78-15755-01 78-15755-01 Troubleshooting the System Hardware Checking the BasicsTroubleshooting the System Hardware Checking the Basics Checking Connections Troubleshooting the System Hardware Checking Connections Maintaining the Cisco Global Site Selector Maintaining Your Site EnvironmentTemperature Humidity AltitudeDust and Particles CorrosionElectrostatic Discharge Electromagnetic and Radio Frequency Interference Power Source Interruptions MagnetismUsing Power Protection Devices Surge ProtectorsUninterruptible Power Supplies Line ConditionersSpecifications Specification DescriptionAppendix a Specifications Connecting a Modem to the GSS 4490 Console Port Configuring a Modem Cabling a Modem to the GSSConfiguring a Modem Figure B-1 Console Port ConnectorCabling a Modem to the GSS Parameters Default Settings Regulatory Compliance and EMI Class a Warnings Regulatory Compliance EMI Class a Warning StatementsRegulatory Compliance EMCEMI Class a Warning Statements FCC Class a Warning Canada Class a WarningCispr 22 Class a Warning Vcci Class a Notice for Japan User may be requested to take appropriate countermeasuresHungary Class a Warning 78-15755-01 D E IN-2 IN-3 IN-4
Related manuals
Manual 20 pages 33.28 Kb Manual 92 pages 54.88 Kb
Top Page Image Contents