Cisco Systems 4490 manual Parameters Default Settings

Page 84

Appendix B Connecting a Modem to the GSS 4490 Console Port

Cabling a Modem to the GSS 4490

2.Make sure that the settings on the remote console match the GSS default settings specified in Table B-2.

Table B-2 GSS Console Port Default Settings

Parameters

Default Settings

 

 

Baud

9600

 

 

Data Bits

8

 

 

Parity

None

 

 

Stop Bits

1

 

 

Terminal Type

VT100/ANSI

 

 

Flow Control

None

 

 

Note When you remotely log in to the GSS 4490 through a modem, make sure that you log out before disconnecting from the session. Use the exec-timeouttimeout command to set the maximum amount of time that the console session can be idle on the GSS 4490 before the GSS 4490 logs it out. By default, the timeout is 150 minutes.

 

Cisco Global Site Selector 4490 Hardware Installation Guide

B-4

78-15755-01

Image 84
Contents Cisco Global Site Selector 4490 Hardware Installation Guide Page Cisco Global Site Selector 4490 Hardware Installation Guide Page N T E N T S Checking Connections Altitude Viii Figure B-1 Page Table A-1 Xii Preface Audience How to Use This Guide Chapter/Appendix DescriptionRelated Documentation Document Title DescriptionSymbols and Conventions XviiBewaar Deze Instructies Varoitus Tärkeitä TurvallisuusohjeitaWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaTA Vare PÅ Disse Instruksjonene Aviso Instruções Importantes DE SegurançaVarning! Viktiga Säkerhetsanvisningar Spara Dessa AnvisningarXxii Introduction IntroductionSystem Hardware Features Cisco Global Site Selector 4490-Front View Hardware Features Front Panel Control ButtonsLED Indicators Front Panel LEDsColor 5shows the location of back panel LEDs, and -3describesInput/Output Ports and Connectors Indicator Color State DescriptionGlobal Site Selector 4490 Back Panel Ports and Receptacles Ethernet Port Pin Number Signal Name RI Ring IndicatorParameters Settings VT100/ANSIChapter Preparing for Installation Safety Warnings Site Requirements Safety GuidelinesSafety Warnings Preparing for Installation Safety Warnings Preparing for Installation Safety Warnings Preparing for Installation Safety Warnings Choosing a Site for Installation Site RequirementsEnsuring Overcurrent Protection Grounding the GSSSafety Guidelines General PrecautionsPreparing for Installation Safety Guidelines Protecting Against Electrostatic Discharge Rack Installation Safety Guidelines Ensuring Proper AirflowStabilizing the System Lifting the SystemPreparing for Installation Safety Guidelines Installing the Cisco Global Site Selector Unpacking and Inspecting the Global Site Selector Tools and Parts Required If the Product is DamagedFour-Post Rack Installation Kit Installing Your Unit Installing the Chassis in a Four-Post Rack Cage nuts Clip nutsRemoving the Inner Slide Rail Attaching the Inner Slide Rail to the GSS Attaching the Slide Rails to the Rack Inserting the Inner Slide Rails Installing the Chassis in a Two-Post Rack Attaching a Bracket to the Right Side of the GSSAttaching the GSS 4490 to the Two-Post Rack Installing the Chassis on a Workbench or Tabletop Connecting Cables Connecting Power Booting the SystemChecking the Front Panel LEDs Color State DescriptionRemoving or Replacing a Cisco Global Site Selector Cisco Global Site Selector 4490 Hardware Installation Guide 78-15755-01 78-15755-01 Troubleshooting the System Hardware Checking the BasicsTroubleshooting the System Hardware Checking the Basics Checking Connections Troubleshooting the System Hardware Checking Connections Maintaining the Cisco Global Site Selector Maintaining Your Site EnvironmentTemperature Humidity AltitudeDust and Particles CorrosionElectrostatic Discharge Electromagnetic and Radio Frequency Interference Power Source Interruptions MagnetismUsing Power Protection Devices Surge ProtectorsUninterruptible Power Supplies Line ConditionersSpecifications Specification DescriptionAppendix a Specifications Connecting a Modem to the GSS 4490 Console Port Configuring a Modem Cabling a Modem to the GSSConfiguring a Modem Figure B-1 Console Port ConnectorCabling a Modem to the GSS Parameters Default Settings Regulatory Compliance and EMI Class a Warnings Regulatory Compliance EMI Class a Warning StatementsRegulatory Compliance EMCEMI Class a Warning Statements FCC Class a Warning Canada Class a WarningCispr 22 Class a Warning Vcci Class a Notice for Japan User may be requested to take appropriate countermeasuresHungary Class a Warning 78-15755-01 D E IN-2 IN-3 IN-4
Related manuals
Manual 20 pages 33.28 Kb Manual 92 pages 54.88 Kb