Cisco Systems RSP7000 manual Formatting the Flash Memory Card

Page 22

Installation Procedures

Step 4 After the system boots the software and initializes the interface processors (approximately 30 seconds for systems with 16 MB of DRAM, and approximately 2 minutes for systems with 64 MB of DRAM), verify that the RSP7000 LEDs are in the following states:

RSP7000 normal LED is on

CPU halt LED is off

Boot error LED is off

Step 5 Verify that all the enabled LEDs (on the interface processors) are on.

When you have verified all the conditions in Steps 2 through 5, the installation is complete.

If you replaced the RSP7000 and saved your configuration file to a remote server before doing so, proceed to the section “Downloading (Retrieving) the Configuration File” on page 16.

If you replaced the RSP7000 and did not save the configuration, use the configure command or the setup command facility to reenter the configuration information.

An error condition exists if no LEDs go on at power up or after initialization, or if the boot error or CPU halt LEDs go on and remain on. If this happens, proceed to the following section, “Troubleshooting the Installation,” to try to isolate the problem.

Formatting the Flash Memory Card

If you had a Flash memory card installed in the PCMCIA slot of your RP and want to use it with your RSP7000, you must first reformat it before you can use it with your new RSP7000. Using the RSP7000, you cannot read data on the RP’s Flash memory card, nor can you use it as bootable media. You must reformat the RP’s Flash card before you can use it with the RSP7000. Flash memory cards formatted on the RP-based systems (7000 series routers) are formatted differently from Flash memory cards formatted on RSP-based systems (7500 series routers).

Caution The formatting procedure erases all information on the Flash memory card. To prevent the loss of important data that might be stored on a Flash memory card, proceed carefully. If you want to save the data on a Flash memory card, copy the data to a server before you format the card.

Note Refer to the section “Saving and Retrieving the Configuration File” on page 12.

227000 Series Route Switch Processor (RSP7000) Installation and Configuration in the Cisco 7000 Series Routers

Image 22
Contents Document Contents What Is the Cisco 7000? Product DescriptionsWhat Is the Cisco 7010? What Is the RSP7000?Product Descriptions Memory Components System SoftwareDram Flash MemoryJumpers Installation PrerequisitesSafety LEDsElectrical Equipment Telephone WiringPreventing Electrostatic Discharge Damage Compatibility Requirements Online Insertion and Removal-An OverviewInstallation Prerequisites Hardware Prerequisites Software PrerequisitesMicrocode Prerequisites Flash Memory Card Replacement and Formatting Prerequisites Saving and Retrieving the Configuration FileUsing the Exec Command Interpreter Using the Ping CommandFollowing example shows the results of a failed ping Uploading Copying the Configuration FileRouter# write net Downloading Retrieving the Configuration File List of Tools and Parts Installation Procedures Removing the RSP7000Replacing the RSP7000 Stop Restarting and Checking the System Formatting the Flash Memory Card Verifying LEDs Troubleshooting the InstallationSystem Power LEDs RSP7000 LEDsNormal System Startup Sequence Interface Processor LEDsTroubleshooting the Installation Troubleshooting the Installation Auxiliary Port Signals Console Port SignalsReference Information Replacing and Upgrading Dram SIMMs RSP7000 Dram SIMMsRemoving SIMMs MEM-RSP-24MReleasing the Simm Spring Clips Installing New SIMMs Handling a SimmSoftware Configuration Register Settings Changing Settings Bit Meanings Off Ones ones Zeros zeros Net zeros Net ones Enabling Booting from Flash Memory Copying to Flash MemoryRouter# squeeze slot0 Recovering a Lost Password Using Flash Memory Cards Installing and Removing a Flash Memory Card Pcmcia slot Replacing a Flash Memory CardFormatting a Flash Memory Card Copying a Bootable Image into a Flash Memory Card Router# config terminal Copying Bootable Images Between Flash Memory Cards Recovering from Locked Blocks Cisco Information Online Cisco Information Online