Cisco Systems RSP7000 manual Formatting a Flash Memory Card

Page 42

Reference Information

Step 2 Insert the card into the appropriate slot until the card completely seats in the connector at the back of the slot and the eject button pops out toward you (See Figure 9b.) Note that the card does not insert all the way inside the RSP7000; a portion of the card will remain outside the slot. Do not attempt to force the card past this point.

Step 3 To eject a card, press the appropriate ejector button until the card is free of the connector at the back of the slot. (See Figure 9c.)

Step 4 Remove the card from the slot and place it in an antistatic bag to protect it.

Formatting a Flash Memory Card

The Flash memory (PCMCIA) card that shipped with your Cisco 7000 contains the Cisco IOS software image. In some cases, you might need to insert a new Flash memory card and copy images or backup configuration files onto it. Before you can use a new Flash memory card, you must format it.

Note The following procedure assumes you have already booted your router.

Warning The following formatting procedure erases all information on the Flash memory card. To prevent the loss of important data on a Flash memory card, proceed carefully. If you wish to save the data on a Flash memory card, upload the data to a server before you format the card.

Use the following procedure to format a new Flash memory card:

Step 1 Using the procedure in the section “Replacing a Flash Memory Card” on page 41 insert the Flash memory card into slot 0. (If slot 0 is not available, use slot 1.)

Step 2 To format the Flash memory card, use the format slot0: (or format slot1:) command as follows. (Use only Intel Series 2+ Flash memory cards.)

Router# format slot0:

All sectors will be erased, proceed? [confirm]

Enter volume id (up to 30 characters): MyNewCard

Formatting sector 1

Format device slot0 completed

Router#

Note For this example, an 8-MB Flash memory card was used, and at the line “Formatting sector,” the system counted the card’s sectors backwards from 64 to 1 as it formatted them. For 16-MB Flash memory cards, the system counts backwards from 128 to 1, and for 20-MB Flash memory cards, the system counts backwards from 160 to 1.

The new Flash memory card is now formatted and ready to use.

Note For complete command descriptions and configuration information, refer to the Router Products Command Reference Addendum (for Cisco IOS Release 10.3) and the Router Products Configuration Guide Addendum (for Cisco IOS Release 10.3).

427000 Series Route Switch Processor (RSP7000) Installation and Configuration in the Cisco 7000 Series Routers

Image 42
Contents Document Contents What Is the Cisco 7000? Product DescriptionsWhat Is the Cisco 7010? What Is the RSP7000?Product Descriptions Memory Components System SoftwareDram Flash MemoryJumpers Installation PrerequisitesSafety LEDsTelephone Wiring Electrical EquipmentPreventing Electrostatic Discharge Damage Compatibility Requirements Online Insertion and Removal-An OverviewInstallation Prerequisites Software Prerequisites Hardware PrerequisitesMicrocode Prerequisites Flash Memory Card Replacement and Formatting Prerequisites Saving and Retrieving the Configuration FileUsing the Exec Command Interpreter Using the Ping CommandFollowing example shows the results of a failed ping Uploading Copying the Configuration FileRouter# write net Downloading Retrieving the Configuration File List of Tools and Parts Installation Procedures Removing the RSP7000Replacing the RSP7000 Stop Restarting and Checking the System Formatting the Flash Memory Card Verifying LEDs Troubleshooting the InstallationSystem Power LEDs RSP7000 LEDsNormal System Startup Sequence Interface Processor LEDsTroubleshooting the Installation Troubleshooting the Installation Console Port Signals Auxiliary Port SignalsReference Information Replacing and Upgrading Dram SIMMs RSP7000 Dram SIMMsRemoving SIMMs MEM-RSP-24MReleasing the Simm Spring Clips Installing New SIMMs Handling a SimmSoftware Configuration Register Settings Changing Settings Bit Meanings Off Ones ones Zeros zeros Net zeros Net ones Enabling Booting from Flash Memory Copying to Flash MemoryRouter# squeeze slot0 Recovering a Lost Password Using Flash Memory Cards Installing and Removing a Flash Memory Card Pcmcia slot Replacing a Flash Memory CardFormatting a Flash Memory Card Copying a Bootable Image into a Flash Memory Card Router# config terminal Copying Bootable Images Between Flash Memory Cards Recovering from Locked Blocks Cisco Information Online Cisco Information Online