Cisco Systems RSP7000 manual Router# config terminal

Page 44

Reference Information

Step 3 To enable the router, copy the image new.image to the Flash memory card, make this image in the Flash memory card (in slot 0) the default boot image, and reboot the router, use the following series of commands:

Router> en

Password:

Router# copy tftp:new.image slot0:new.image

20575008 bytes available on device slot0, proceed? [confirm] Address or name of remote host [1.1.1.1]?

Loading new.image from 1.1.1.1 (via Ethernet1/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[OK - 7799951/15599616 bytes]

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC Router#

Note In the previous example, the exclamation points (!!!) appear as the ﬁle is downloaded and the “C” characters signify calculation of the checksum, which is a veriﬁcation that the ﬁle has been correctly downloaded to the Flash memory card.

Router# config terminal

Router(config)# no boot system

Router(config)# boot system flash slot0:new.image

Router(config)# ^z

Router# copy running-config startup-config

Router# reload

When the system reloads it will boot the image new.image from the Flash memory card in slot 0.

447000 Series Route Switch Processor (RSP7000) Installation and Conﬁguration in the Cisco 7000 Series Routers

Image 44

Contents Document Contents What Is the Cisco 7000? Product DescriptionsWhat Is the Cisco 7010? What Is the RSP7000?Product Descriptions Memory Components System SoftwareDram Flash MemoryInstallation Prerequisites SafetyJumpers LEDsPreventing Electrostatic Discharge Damage Telephone WiringElectrical Equipment Compatibility Requirements Online Insertion and Removal-An OverviewInstallation Prerequisites Microcode Prerequisites Software PrerequisitesHardware Prerequisites Flash Memory Card Replacement and Formatting Prerequisites Saving and Retrieving the Conﬁguration FileUsing the Exec Command Interpreter Using the Ping CommandFollowing example shows the results of a failed ping Uploading Copying the Conﬁguration FileRouter# write net Downloading Retrieving the Conﬁguration File List of Tools and Parts Installation Procedures Removing the RSP7000Replacing the RSP7000 Stop Restarting and Checking the System Formatting the Flash Memory Card Troubleshooting the Installation System Power LEDsVerifying LEDs RSP7000 LEDsNormal System Startup Sequence Interface Processor LEDsTroubleshooting the Installation Troubleshooting the Installation Reference Information Console Port SignalsAuxiliary Port Signals Replacing and Upgrading Dram SIMMs RSP7000 Dram SIMMsRemoving SIMMs MEM-RSP-24MReleasing the Simm Spring Clips Installing New SIMMs Handling a SimmSoftware Conﬁguration Register Settings Changing Settings Bit Meanings Off Ones ones Zeros zeros Net zeros Net ones Enabling Booting from Flash Memory Copying to Flash MemoryRouter# squeeze slot0 Recovering a Lost Password Using Flash Memory Cards Installing and Removing a Flash Memory Card Pcmcia slot Replacing a Flash Memory CardFormatting a Flash Memory Card Copying a Bootable Image into a Flash Memory Card Router# config terminal Copying Bootable Images Between Flash Memory Cards Recovering from Locked Blocks Cisco Information Online Cisco Information Online