Cisco Systems RSP7000 manual Document Contents

Page 1

Doc. No. 78-2561-01

7000 Series Route Switch Processor (RSP7000)

Installation and Configuration in

the Cisco 7000 Series Routers

Product Numbers: RSP7000=, MEM-RSP-FLC8M=, MEM-RSP-FLC16M=,

MEM-RSP-FLC20M=, MEM-RSP-8M=, MEM-RSP-16M, MEM-RSP-24M,

MEM-RSP-32M(=), MEM-RSP-64M(=), and MEM-RSP-128M(=)

This document discusses the 7000 Series Route Switch Processor (RSP7000), which is a new main processor module for the Cisco 7000 series routers: the Cisco 7000 and the Cisco 7010. The RSP7000 combines all of the switched routing and high-speed switching functions required by the Cisco 7000 series routers. (Refer to the section “What Is the RSP7000?” on page 3.)

The RSP7000 requires that your Cisco 7000 series router is running Cisco Internetwork Operating

System (Cisco IOS) Release 10.3(9), or later, Release 11.0(6), or later, or Release 11.1(1) or later.

Caution Using the RSP7000 in your Cisco 7000 series router might require that some currently installed interface processors be upgraded to specific, compatible hardware versions; otherwise, error messages and erratic system behavior might result. You can use the show diag command to see which interface processors in your system need this hardware upgrade. For a complete list of the potentially affected interface processors, their required hardware versions, and information on upgrading your affected interface processors, refer to the document Verifying Interface Processor Compatibility with the Cisco 7500 Series Investment Protection Program (IPP), Document Number 78-2077-xx, where xx refers to the latest version of this document.

Document Contents

Following are the sections in this document:

Product Descriptions, page 2

Installation Prerequisites, page 7

Installation Procedures, page 18

Troubleshooting the Installation, page 23

Reference Information, page 28

Cisco Information Online, page 47

Copyright © 1996

1

Cisco Systems, Inc.

All rights reserved.

Image 1
Contents Document Contents Product Descriptions What Is the Cisco 7000?What Is the RSP7000? What Is the Cisco 7010?Product Descriptions System Software Memory ComponentsFlash Memory DramSafety Installation PrerequisitesJumpers LEDsElectrical Equipment Telephone WiringPreventing Electrostatic Discharge Damage Online Insertion and Removal-An Overview Compatibility RequirementsInstallation Prerequisites Hardware Prerequisites Software PrerequisitesMicrocode Prerequisites Saving and Retrieving the Configuration File Flash Memory Card Replacement and Formatting PrerequisitesUsing the Ping Command Using the Exec Command InterpreterUploading Copying the Configuration File Following example shows the results of a failed pingRouter# write net Downloading Retrieving the Configuration File List of Tools and Parts Removing the RSP7000 Installation ProceduresReplacing the RSP7000 Stop Restarting and Checking the System Formatting the Flash Memory Card System Power LEDs Troubleshooting the InstallationVerifying LEDs RSP7000 LEDsNormal Interface Processor LEDs System Startup SequenceTroubleshooting the Installation Troubleshooting the Installation Auxiliary Port Signals Console Port SignalsReference Information RSP7000 Dram SIMMs Replacing and Upgrading Dram SIMMsMEM-RSP-24M Removing SIMMsReleasing the Simm Spring Clips Handling a Simm Installing New SIMMsSoftware Configuration Register Settings Changing Settings Bit Meanings Off Ones ones Zeros zeros Net zeros Net ones Copying to Flash Memory Enabling Booting from Flash MemoryRouter# squeeze slot0 Recovering a Lost Password Using Flash Memory Cards Replacing a Flash Memory Card Installing and Removing a Flash Memory Card Pcmcia slotFormatting a Flash Memory Card Copying a Bootable Image into a Flash Memory Card Router# config terminal Copying Bootable Images Between Flash Memory Cards Recovering from Locked Blocks Cisco Information Online Cisco Information Online