Cisco Systems 1200 Safety Information, FCC Safety Compliance Statement, General Safety Guidelines

Page 29

Chapter 2 Installing the Access Point

Safety Information

Safety Information

Follow the guidelines in this section to ensure proper operation and safe use of the access point.

FCC Safety Compliance Statement

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.

General Safety Guidelines

•Do not touch or move antenna(s) while the unit is transmitting or receiving.

•Do not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.

•The use of wireless devices in hazardous locations is limited to the constraints posed by the local codes, the national codes, and the safety directors of such environments.

Warnings

Translated versions of all safety warnings are available in the safety warning document that shipped with your access point or on Cisco.com. To browse to the document on Cisco.com, refer to Appendix A, “Translated Safety Warnings” for instructions.

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 245B

Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. Statement 332

Cisco Aironet 1200 Series Access Point Hardware Installation Guide

	OL-8370-04	2-2

Image 29

Contents Americas Headquarters Page N T E N T S Overview Mode Button Setting Console Cable Pinouts E-1 Console Port Signals and Pinouts E-2 Viii Audience PrefacePurpose OrganizationConventions Preface Conventions Related Publications Xiii Locating the Product Serial NumberXiv Product Terminology Autonomous Access PointsOverview Lightweight Access Points Guidelines for Using 1200 Series Lightweight Access Points Hardware FeaturesDual-Radio Operation LEDs Console Port Network Examples with Autonomous Access Points Access point Root Access Point on a Wired LANAccess Point as Repeater Repeater Unit that Extends Wireless RangeBridge Network with Wireless Clients Central Unit in an All-Wireless NetworkWorkgroup Bridge Network Point-to-Point Bridge ConfigurationNetwork Example with Lightweight Access Points Page Installing the Access Point General Safety Guidelines Safety InformationFCC Safety Compliance Statement Package Contents Unpacking the Access PointController Discovery Process for Lightweight Access Points Basic Installation GuidelinesAccess Point Layout and Connectors Before Beginning the InstallationRM22A Radio Module with External RP-TNC Antenna Connectors Deploying the Access Points on the Wireless Network Connecting the 5-GHz External Antennas Connecting the 2.4-GHz AntennasAccess Point Power Options Connecting the Ethernet and Power CablesConnecting to an Ethernet Network with Local Power OL-8370-04 Mounting Instructions Mounting Bracket OverviewMounting on a Horizontal or Vertical Surface Mounting Bracket Parts Mounting Below a Suspended CeilingMounting Above a Suspended Ceiling It may be helpful to refer to -3before proceeding Access Point Mounting Bracket Securing the Access Point to the Mounting Bracket Attaching the Access Point to the Mounting BracketUpgrading the 2.4-GHz Radio Unpacking the Radio Upgrade OverviewLocation of 2.4-GHz Radio Access Cover Screw Opening the Access CoverLocation of Retaining Clips on Blank Spacer Card Removing a Blank Spacer CardRemoving a 2.4-GHz Radio Location of Retaining Clips on 2.4-GHz Radio Card Antenna Connector Labels and Mini-PCI Connector Installing a 2.4-GHz RadioUpgrading the 2.4-GHz Radio Installing a 2.4-GHz Radio Attaching the Compliance Labels Access Point Compliance LabelsPlacing the Labels Upgrading the 5-GHz Radio Module Unpacking the Radio Module Removing the 5-GHz Radio Access CoverRemoving a 5-GHz Radio Module Mounting screws Access point GHz radio module antennaRemoving the 5-GHz Radio Module Installing a 5-GHz Radio Module RM20A or RM21A Shown Installing a 5-GHz Radio ModuleGHz radio module antenna Mounting screws Attaching the Compliance Label Access Point Compliance Label LocationsLocations for Compliance Labels Troubleshooting Autonomous Access Points Checking the Top Panel LEDs LED Default IP Address Behavior Checking Basic SettingsDefault Ssid and Radio Behavior Enabling the Radio InterfacesWEP Keys Security SettingsRunning the Carrier Busy Test Running the Ping or Link Test Using the Mode Button Resetting to the Default ConfigurationUsing the Web Browser Interface Reloading the Access Point ImageRadio Upgrade Required Cisco IOS Software Release Browser Http Interface Web Browser InterfaceBrowser Tftp Interface Obtaining the Access Point Image FileHttp//tftpd32.jounin.net Obtaining the Tftp Server SoftwareConnecting the Serial Cable Connecting to the Access Point LocallyOL-8370-04 Troubleshooting Lightweight Access Points Using Dhcp Option Checking the Top Panel LEDs Message Ethernet Status Radio Type Clearing Manually Entered Controller Information Configuring Controller InformationManually Resetting the Access Point to Defaults Returning the Access Point to Autonomous ModeMode Button Setting Obtaining the Autonomous Access Point Image File Obtaining the Tftp Server Software OL-8370-04 Translated Safety Warnings OL-8370-04 Declarations of Conformity and Regulatory Information For Home or Office USE AIR-ANT2410Y-R Canadian Compliance Statement Vcci Statement for Japan Industry CanadaPage EMC Declaration of Conformity for RF Exposure Japanese Translation Chinese Translation English Translation Access Points with Ieee 802.11a RadiosAll Access Points Access Point Models Operation of Cisco Aironet Access Points in BrazilDeclaration of Conformity Statements Page OL-8370-04 Page OL-8370-04 Page Declaration of Conformity Product AIR-AP1232AG-E-K9 Declaration of Conformity Annex to DofC# Information on Antennas and Power Levels OL-8370-04 Access Point with 802.11a Radio Module Access Point SpecificationsAppendix C Access Point Specifications Category Access Point with 802.11b or 802.11g Radio CCK Ofdm Access Point with 802.11a Radio Module Arib STD-66 Channels and Maximum Power Levels OL-8370-04 Console Cable Pinouts TXD RXD GND Console Port Signals and PinoutsPriming Lightweight Access Points Prior to Deployment OL-8370-04 Page OL-8370-04 Access Points Access Point Vendor Class Identifier VCI Configuring Option 43 for 1000 Series Access PointsAdd the option 60 line using the following syntax Type + Length + Value O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2

Related manuals

Manual 7 pages 38.21 Kb