Cisco Systems 1200 manual Locations for Compliance Labels

Page 64

Chapter 5 Upgrading the 5-GHz Radio Module

Installing a 5-GHz Radio Module

Step 1 Check the product compliance label to identify the model number of your 1200 series access point. Step 2 Refer to Figure 5-6for the compliance label locations.

Step 3 Use the matrix in Table 5-1to decide which labels to use and where to place them on the access point.

	Table 5-1	Locations for Compliance Labels

	1200 Series		AIR-RM21A-x-K9 or AIR-RM22A-x-K9	AIR-AP1210-x-K9 Product
	Model		Radio Compliance Label	Compliance Label

	AIR-AP1220A		Place over existing AIR-RM20A-x-K9	Place over existing product compliance
			radio compliance label or location 3 if no	label.
	AIR-AP1230A		radio compliance label or location 3 if no	label.
	AIR-AP1230A		label exists.

	All other models			Discard product compliance label.
	All other models			Discard product compliance label.

Step 4 Discard any labels that you did not use.

The 5-GHz radio module installation is now complete and radio settings are at default values. To configure the 5-GHz radio with your wireless network settings refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points.

Cisco Aironet 1200 Series Access Point Hardware Installation Guide

5-8	OL-8370-04

Image 64

Contents Americas Headquarters Page N T E N T S Overview Mode Button Setting Console Cable Pinouts E-1 Console Port Signals and Pinouts E-2 Viii Preface AudiencePurpose OrganizationConventions Preface Conventions Related Publications Locating the Product Serial Number XiiiXiv Overview Autonomous Access PointsProduct Terminology Lightweight Access Points Hardware Features Guidelines for Using 1200 Series Lightweight Access PointsDual-Radio Operation LEDs Console Port Network Examples with Autonomous Access Points Root Access Point on a Wired LAN Access pointRepeater Unit that Extends Wireless Range Access Point as RepeaterCentral Unit in an All-Wireless Network Bridge Network with Wireless ClientsPoint-to-Point Bridge Configuration Workgroup Bridge NetworkNetwork Example with Lightweight Access Points Page Installing the Access Point FCC Safety Compliance Statement Safety InformationGeneral Safety Guidelines Unpacking the Access Point Package ContentsBasic Installation Guidelines Controller Discovery Process for Lightweight Access PointsBefore Beginning the Installation Access Point Layout and ConnectorsRM22A Radio Module with External RP-TNC Antenna Connectors Deploying the Access Points on the Wireless Network Connecting the 2.4-GHz Antennas Connecting the 5-GHz External AntennasConnecting the Ethernet and Power Cables Access Point Power OptionsConnecting to an Ethernet Network with Local Power OL-8370-04 Mounting Instructions Overview Mounting BracketMounting on a Horizontal or Vertical Surface Mounting Below a Suspended Ceiling Mounting Bracket PartsMounting Above a Suspended Ceiling It may be helpful to refer to -3before proceeding Access Point Mounting Bracket Attaching the Access Point to the Mounting Bracket Securing the Access Point to the Mounting BracketUpgrading the 2.4-GHz Radio Upgrade Overview Unpacking the RadioOpening the Access Cover Location of 2.4-GHz Radio Access Cover ScrewRemoving a Blank Spacer Card Location of Retaining Clips on Blank Spacer CardRemoving a 2.4-GHz Radio Location of Retaining Clips on 2.4-GHz Radio Card Installing a 2.4-GHz Radio Antenna Connector Labels and Mini-PCI ConnectorUpgrading the 2.4-GHz Radio Installing a 2.4-GHz Radio Access Point Compliance Labels Attaching the Compliance LabelsPlacing the Labels Upgrading the 5-GHz Radio Module Removing the 5-GHz Radio Access Cover Unpacking the Radio ModuleMounting screws Access point GHz radio module antenna Removing a 5-GHz Radio ModuleRemoving the 5-GHz Radio Module Installing a 5-GHz Radio Module Installing a 5-GHz Radio Module RM20A or RM21A ShownGHz radio module antenna Mounting screws Access Point Compliance Label Locations Attaching the Compliance LabelLocations for Compliance Labels Troubleshooting Autonomous Access Points Checking the Top Panel LEDs LED Checking Basic Settings Default IP Address BehaviorDefault Ssid and Radio Behavior Enabling the Radio InterfacesRunning the Carrier Busy Test Security SettingsWEP Keys Running the Ping or Link Test Resetting to the Default Configuration Using the Mode ButtonReloading the Access Point Image Using the Web Browser InterfaceRadio Upgrade Required Cisco IOS Software Release Web Browser Interface Browser Http InterfaceObtaining the Access Point Image File Browser Tftp InterfaceObtaining the Tftp Server Software Http//tftpd32.jounin.netConnecting to the Access Point Locally Connecting the Serial CableOL-8370-04 Troubleshooting Lightweight Access Points Using Dhcp Option Checking the Top Panel LEDs Message Ethernet Status Radio Type Configuring Controller Information Clearing Manually Entered Controller InformationReturning the Access Point to Autonomous Mode Manually Resetting the Access Point to DefaultsMode Button Setting Obtaining the Autonomous Access Point Image File Obtaining the Tftp Server Software OL-8370-04 Translated Safety Warnings OL-8370-04 Declarations of Conformity and Regulatory Information For Home or Office USE AIR-ANT2410Y-R Vcci Statement for Japan Industry Canada Canadian Compliance StatementPage EMC Declaration of Conformity for RF Exposure Japanese Translation Access Points with Ieee 802.11a Radios Chinese Translation English TranslationAll Access Points Operation of Cisco Aironet Access Points in Brazil Access Point ModelsDeclaration of Conformity Statements Page OL-8370-04 Page OL-8370-04 Page Declaration of Conformity Product AIR-AP1232AG-E-K9 Declaration of Conformity Annex to DofC# Information on Antennas and Power Levels OL-8370-04 Access Point Specifications Access Point with 802.11a Radio ModuleAppendix C Access Point Specifications Category Access Point with 802.11b or 802.11g Radio CCK Ofdm Access Point with 802.11a Radio Module Arib STD-66 Channels and Maximum Power Levels OL-8370-04 Console Cable Pinouts Console Port Signals and Pinouts TXD RXD GNDPriming Lightweight Access Points Prior to Deployment OL-8370-04 Page OL-8370-04 Access Points Configuring Option 43 for 1000 Series Access Points Access Point Vendor Class Identifier VCIAdd the option 60 line using the following syntax Type + Length + Value O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2

Related manuals

Manual 7 pages 38.21 Kb