Cisco Systems NOREGILMI manual ATM0/0/3 47.0091.8100.0000.0060.3e5a.4501.00d0.069a.7c40/152

Page 8

R

I 1

ATM2/0/0

UP 0

47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4501/152

R

I 1

ATM2/0/0

UP 0

47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4502/152

R

I 1

ATM2/0/0

UP 0

47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4503/152

R

I 1

ATM2/0/0

UP 0

47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4504/152

R

I 1

ATM2/0/0

UP 0

47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4505/152

S

E 1

ATM0/0/3

UP 0

47.0091.8100.0000.0060.3e5a.4501.00d0.069a.7c40/152

R

I 1

ATM2/0/0

UP 0

47.0091.8100.0000.0060.3e5a.4501.4000.0c/128

Casimir# show running−config

Building configuration...

Current configuration:

!

!Last configuration change at 12:28:24 UTC Mon Apr 2 2001

!NVRAM config last updated at 12:28:25 UTC Mon Apr 2 2001

version 12.0

!−−− Output suppressed.

atm route 47.0091.8100.0000.0060.3e5a.4501.00d0.069a.7c40... ATM0/0/3

As shown above, the NSAP address has been statically configured on the switch and in this case even points to a different interface from the one where it should be located.

When the NSAP Address Is Registered via ILMI by Another Device

To simulate this scenario, Tintin and Bernard are configured with the same MAC address.

Bernard

interface ATM2/0/0

mac−address 0000.0000.0001 pvc 0/16 ilmi

!

pvc 0/5 qsaal

Tintin

interface ATM1/0

mac−address 0000.0000.0001 no ip address

atm pvc 1 0 5 qsaal atm pvc 2 0 16 ilmi

Because they are both connected to the same switch, the NSAP address associated to the LECs configured on the sub−interfaces atm 2/0/0.1 and atm 1/0.1 is the same: 47.00918100000000603E5A4501.000000000001.01.

Tintin interface atm 1/0.1 has been brought up before atm 2/0/0.1 on Bernard. Therefore, Tintin is the first one to register the NSAP address 47.00918100000000603E5A4501.000000000001.01 via ILMI. As soon as the interface atm 2/0/0.1 is brought up on Bernard, this message is displayed:

1w1d: %LANE−3−NOREGILMI: ATM2/0/0.1 LEC cannot register 47.00918100000000603E5A4501.000000000001.01 with ILMI

Cisco − ILMI Address Registration Problems: %LANE−3−NOREGILMI

Image 8
Contents Table of Contents Introduction PrerequisitesDocument ID RequirementsAssociated Error Message ConfigureNetwork Diagram ConventionsConfigurations Both Bernard and Tintin are configured with a LECChecking Ilmi Ilmi StatusWhen Ilmi is Disabled on the Switch Interface This has the following result ∙ show atm pvc 0/16 ∙ show atm vc vcdBernard# show atm ilmi−st InPkts 255, OutPkts 309, InBytes 18842, OutBytesOn the router Bernard, you can see this message If the Switch Knows the Nsap AddressKnown Caveats Casimir# show running−config ATM0/0/3 47.0091.8100.0000.0060.3e5a.4501.00d0.069a.7c40/152ATM Address 47.00918100000000603E5A4501.000000000001.01 BernardTintin# show lane client Casimir 1w1d ILMIATM2/0/0 Errored or no response receivedLane config fixed−config−atm−address No atm address−registration Configuration ProblemsLane config database test Updated May 11 Document ID Related Information