Cisco Systems NOREGILMI manual Casimir, 1w1d ILMIATM2/0/0 Errored or no response received

Page 10

1w1d: ILMI(ATM2/0/0):Updating ES Database with 7.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4502.00

1w1d: Reg Status :− Delete in progress − False, Add in progress − True

1w1d: ILMI(ATM2/0/0):Response received for request 930

1w1d: ILMI(ATM2/0/0): Errored response <General Error> Function Type = ilmiReqOther

1w1d: ILMI(ATM2/0/0): Errored or no response received

1w1d: ILMI(ATM2/0/0): ES database update not done

1w1d: ILMI(ATM2/0/0):Updating ES Database with 47.0091.8100.0000.0060.3e5a.4501.0000.0000.0001.01

1w1d: Reg Status :− Delete in progress − False, Add in progress − True

1w1d: %LANE−3−NOREGILMI: ATM2/0/0.1 LEC cannot register 47.00918100000000603E5A4501.000000000001.01 with ILMI

!−−− Output suppressed.

Casimir:

!−−− Output suppressed.

Apr 2 13:10:06.800: ILMI: Validating address 47.0091.8100.0000.0060.3e5a.4501.0000.0000.00

Apr 2 13:10:06.800: ILMI: Address rejected by Client identified as pnni(ATM0/0/0)

!−−− Output suppressed.

Note: The situation described in this section can often be encountered in the following scenario. If LECS services are configured on Cisco devices and other vendor devices at the same time and all these LECS are listening to the well−known address and advertising it, this message can be displayed:

1w2d: %LANE−3−NOREGILMI: ATM2/0/0 LECS cannot register 47.007900000000000000000000.00A03E000001.00 with ILMI

As LECS are configured on non−Cisco devices as well as Cisco devices, you cannot use SSRP of Fast−SSRP. The purpose of these redundancy protocols is that one LECS is elected as Master LECS (the others being backup LECS). The master LECS is the only one allowed to advertise the well−known address if it is being used. In this case, since you cannot configure a redundancy protocol, there is no Master LECS election. Hence, all the LECS try to advertise the well−known address, but only one succeeds.

To illustrate this, the configurations have been modified as shown:

Bernard

lane database test

name ilmi−test server−atm−address 47.00918100000000603E5A4501.00603E5A4503.01

!

interface ATM2/0/0 no ip address

no ip route−cache distributed no atm ilmi−keepalive

pvc 0/16 ilmi

!

pvc 0/5 qsaal

!

lane config fixed−config−atm−address

Cisco − ILMI Address Registration Problems: %LANE−3−NOREGILMI

Image 10
Contents Table of Contents Document ID IntroductionPrerequisites RequirementsNetwork Diagram Associated Error MessageConfigure ConventionsChecking Ilmi ConfigurationsBoth Bernard and Tintin are configured with a LEC Ilmi StatusWhen Ilmi is Disabled on the Switch Interface Bernard# show atm ilmi−st This has the following result∙ show atm pvc 0/16 ∙ show atm vc vcd InPkts 255, OutPkts 309, InBytes 18842, OutBytesKnown Caveats If the Switch Knows the Nsap AddressOn the router Bernard, you can see this message Casimir# show running−config ATM0/0/3 47.0091.8100.0000.0060.3e5a.4501.00d0.069a.7c40/152Tintin# show lane client BernardATM Address 47.00918100000000603E5A4501.000000000001.01 Lane config fixed−config−atm−address 1w1d ILMIATM2/0/0 Errored or no response receivedCasimir Lane config database test Configuration ProblemsNo atm address−registration Updated May 11 Document ID Related Information