Cisco Systems OL-7822-06 quick start Parameter Definition

Page 25

Chapter 4 Connect the Management Interfaces and Perform Initial System Configuration

Perform the Initial System Configuration

Table 4-1

Setup Command Parameters (continued)

 

 

 

Parameter

 

Definition

 

 

Access Control List number

How many ACLs will be necessary? What IP

 

 

addresses will be permitted/denied access for each

 

 

management interface? You may want ACLs for

 

 

the following:

 

 

•

Any IP access

 

 

•

Telnet access

 

 

•

SNMP GET access

 

 

•

SNMP SET access

 

 

list entries (maximum 20 per list)

IP address, and whether permitted or denied

 

 

access.

 

 

 

IP access ACL

 

ID number of the ACL controlling IP access.

 

 

 

telnet ACL

 

ID number of the ACL controlling telnet access.

 

 

SNMP agent status

Enable or disable SNMP management.

 

 

GET community names

Community strings to allow GET access and

 

 

associated ACLs (maximum 20).

 

 

SET community names

Community strings to allow SET access and

 

 

associated ACLs (maximum 20).

 

 

trap managers (maximum 20)

Trap manager IP address, community string, and

 

 

SNMP version.

 

 

Authentication Failure trap status

Sets the status of the Authentication Failure traps.

 

 

enterprise traps status

Sets the status of the enterprise traps.

 

 

system administrator

Name of the system administrator.

 

 

 

Topology Configuration

 

 

 

 

connection mode

Is the SCE 1000 installed using inline topology or

 

 

receive-only topology using an optical splitter?

 

 

link bypass mode on operational status

When the SCE 1000 is operational, should it

 

 

bypass traffic or not?

 

 

link bypass mode on non-operational status

When the SCE 1000 is not operational, should it

 

 

bypass traffic or cut it off?

 

 

 

priority

 

If this is a cascaded topology, is this SCE 1000 the

(cascade topology only)

primary or secondary SCE 1000?

 

 

 

 

operational status of the SCE after abnormal boot

After a reboot due to a failure, should the SCE

 

 

1000 remain in a Failure status or move to

 

 

operational status provided no other problem was

 

 

detected?

 

 

 

 

Following are some general instructions regarding the setup dialog:

•All default values appear in square brackets [default] .

If no value appears in the brackets [], or more than one option appears [ yes/no ], then this parameter does not have a default value.

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

 

OL-7822-06

4-5

 

 

 

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Cisco Service Control Engine 1000 2xGBE Quick Start Guide Page N T E N T S Example Example 2 Installing a Service Control Application OL-7822-06 Site Preparation and Unpacking Information About Preparing for InstallationPrepare for Rack-Mount Installation Workbench or Tabletop InstallationTools and Parts Prepare for Installation Workbench or Tabletop Installation OL-7822-06 SCE 1000 Mounting Brackets Rack-Mount the SCEAttaching the Mounting Brackets 4-post Attach the Brackets to the SCEAssemble the Crossrail Supports Installing the Crossrail Supports Four-post rack onlyAttach the Crossrail Supports to the Rack Mount the System to the RackSummary Steps Securing the SCE Platform to the Rack Connect the Chassis Ground Connect the Power Supply UnitsGrounding the Unit DC Connecting the PowerConnecting the DC Power Connect the DC-Input Power Supply UnitConnecting the AC Power Connect the AC-Input Power Supply UnitConnect the Local Console Connecting to the Local ConsoleInitial System Configuration Perform the Initial System ConfigurationSetup Command Setup Command Parameters Parameter Definition Example Configuring Initial SettingsSetting the Passwords Configuring the HostnameExample Configuring Time SettingsEnter time zone name UTC CET Enter time interval in seconds between unicast updates Configuring the DNS SettingsEnter Primary DNS IP address Configuring Access Control Lists ACLs Configuring the RDR Formatter DestinationInitial IP address Wildcard bits Range Deny Permit any Examples Configuring Snmp Enter the Snmp configuration menu Type the trap manager community string and press press Enter Enter Snmp trap manager community string About the Topology-Dependent Parameters Configuring the Topology-Dependent ParametersExample 1, Example 2, Example 3, Completing and Saving the Configuration Apply and Save this configuration? yes/no Examples Example Connect the Management InterfaceOL-7822-06 Single Link Inline Topology Information About CablingSingle Link Receive-only Topology Bump-in-the-Wire InstallationCabling the Line Interfaces Configure GigabitEthernet Auto-NegotiationConnect the GBE Line Interface Ports SCE Model Transceiver Transmit Power Receive Power DistanceCable the Line Ports Cabling the Line Interfaces OL-7822-06 Final Tests Examining the LEDsVerifying Operational Status Viewing the User Log Counters Saving the Configuration Settings Examples Following example shows the running configuration fileLoading and Activating a Service Control Application Advanced Configuration of the SCE PlatformOL-7822-06 SCE 1000 Operational Status Troubleshoot Startup ProblemsTroubleshoot Startup Problems SCE 1000 Operational Status CLI Commands for Troubleshooting Identifying Startup ProblemsTroubleshooting the link interface subsystem Page OL-7822-06

OL-7822-06 specifications

Cisco Systems OL-7822-06 is a comprehensive course offered within the Cisco Networking Academy, designed to equip students and professionals with a deep understanding of basic networking concepts and advanced networking technologies. This course primarily focuses on the required skills and knowledge needed for building, running, and maintaining networks and prepares participants for various roles in the IT and cybersecurity sectors.

One of the main features of the OL-7822-06 course is its thorough curriculum, which covers key topics such as networking fundamentals, including OSI and TCP/IP models, IPv4 and IPv6 addressing, and subnetting. It dives deep into network protocols, ensuring learners acquire a firm grasp of how data flows across networks, as well as the role of routers and switches in maintaining efficient network operations.

The course also emphasizes hands-on learning, leveraging various simulation tools and virtual labs that provide students with real-world scenarios to apply their knowledge practically. These labs are integral in helping learners understand the configuration and troubleshooting of network devices, enhancing their problem-solving skills in a controlled environment.

Another significant aspect of OL-7822-06 is its focus on emerging technologies. The course introduces students to concepts such as network security, cloud computing, wireless networking, and IoT (Internet of Things). This inclusion reflects the ever-evolving landscape of technology and prepares participants to be adaptable in the face of rapid change within the industry.

Additionally, the OL-7822-06 course promotes collaboration and peer engagement through group projects and discussions. This not only fosters a sense of community among learners but also enhances their communication skills, which are essential in modern IT environments.

The course is structured to accommodate various learning styles, offering a blend of theoretical knowledge and practical exercises. It provides assessments and quizzes that help gauge understanding and retention of information, ensuring students are well-prepared for certification exams and real-world applications.

In summary, Cisco Systems OL-7822-06 stands out as a robust educational offering that combines foundational networking principles with advanced technologies. Its focus on hands-on experience, collaboration, and the introduction of current industry trends makes it an invaluable resource for aspiring networking professionals, ultimately paving the way for a successful career in the tech industry.
Top Page Image Contents