Cisco Systems OL-7822-06 quick start Summary Steps

Page 15

Chapter 2 Rack-Mount the SCE 1000

Mount the System to the Rack

SUMMARY STEPS

1.Make sure that the rack brakes are locked or that the rack is otherwise stabilized.

2.Position the SCE 1000 so that the front end is closest to you, and lift it carefully to place it into the rack. To prevent injury, avoid sudden twists or moves.

3.Slide the SCE 1000 into the rack, pushing it back until the brackets (installed at the front of the SCE 1000) meet the mounting strips or posts on both sides of the rack.

4.While keeping the brackets flush against the posts or mounting strips, align the holes in the brackets with the holes on the rack or mounting strip.

5.For each bracket, insert and tighten two appropriate screws to the rack.

DETAILED STEPS

Step 1 Make sure that the rack brakes are locked or that the rack is otherwise stabilized.

Figure 2-7 Sliding the SCE Platform into the Rack

MNG 1

MNG 2

ALINK/ 10/100/

LINK/ 10/100/

CTIVE 1000

 

ACTIVE 1000

CONSOLE

AUX

PWR A

PWR B

STATUS BYPASS

 

 

LINK RX

TX

 

LINK RX

 

 

 

 

 

TX

RX

MM

TX

 

 

 

 

 

 

RX

MM

 

 

 

 

 

 

TX

 

SUB

GBE-1

 

 

 

 

LINE

 

 

 

 

 

 

 

 

NET

 

Cisco

1000

SCE

2xGBE

Series

210419

1

2

3

Step 2 Position the SCE 1000 so that the front end is closest to you, and lift it carefully to place it into the rack. To prevent injury, avoid sudden twists or moves.

Step 3 Slide the SCE 1000 into the rack, pushing it back until the brackets (installed at the front of the SCE 1000) meet the mounting strips or posts on both sides of the rack.

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

 

OL-7822-06

2-5

 

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Cisco Service Control Engine 1000 2xGBE Quick Start Guide Page N T E N T S Example Example 2 Installing a Service Control Application OL-7822-06 Site Preparation and Unpacking Information About Preparing for InstallationWorkbench or Tabletop Installation Prepare for Rack-Mount InstallationTools and Parts Prepare for Installation Workbench or Tabletop Installation OL-7822-06 SCE 1000 Mounting Brackets Rack-Mount the SCEAttaching the Mounting Brackets 4-post Attach the Brackets to the SCEAssemble the Crossrail Supports Installing the Crossrail Supports Four-post rack onlyAttach the Crossrail Supports to the Rack Mount the System to the RackSummary Steps Securing the SCE Platform to the Rack Connect the Chassis Ground Connect the Power Supply UnitsGrounding the Unit DC Connecting the PowerConnecting the DC Power Connect the DC-Input Power Supply UnitConnecting the AC Power Connect the AC-Input Power Supply UnitConnect the Local Console Connecting to the Local ConsoleInitial System Configuration Perform the Initial System ConfigurationSetup Command Setup Command Parameters Parameter Definition Example Configuring Initial SettingsSetting the Passwords Configuring the HostnameExample Configuring Time SettingsEnter time zone name UTC CET Enter time interval in seconds between unicast updates Configuring the DNS SettingsEnter Primary DNS IP address Configuring Access Control Lists ACLs Configuring the RDR Formatter DestinationInitial IP address Wildcard bits Range Deny Permit any Examples Configuring Snmp Enter the Snmp configuration menu Type the trap manager community string and press press Enter Enter Snmp trap manager community string About the Topology-Dependent Parameters Configuring the Topology-Dependent ParametersExample 1, Example 2, Example 3, Completing and Saving the Configuration Apply and Save this configuration? yes/no Examples Example Connect the Management InterfaceOL-7822-06 Single Link Inline Topology Information About CablingSingle Link Receive-only Topology Bump-in-the-Wire InstallationCabling the Line Interfaces Configure GigabitEthernet Auto-NegotiationConnect the GBE Line Interface Ports SCE Model Transceiver Transmit Power Receive Power DistanceCable the Line Ports Cabling the Line Interfaces OL-7822-06 Examining the LEDs Final TestsVerifying Operational Status Viewing the User Log Counters Saving the Configuration Settings Examples Following example shows the running configuration fileLoading and Activating a Service Control Application Advanced Configuration of the SCE PlatformOL-7822-06 SCE 1000 Operational Status Troubleshoot Startup ProblemsTroubleshoot Startup Problems SCE 1000 Operational Status CLI Commands for Troubleshooting Identifying Startup ProblemsTroubleshooting the link interface subsystem Page OL-7822-06

OL-7822-06 specifications

Cisco Systems OL-7822-06 is a comprehensive course offered within the Cisco Networking Academy, designed to equip students and professionals with a deep understanding of basic networking concepts and advanced networking technologies. This course primarily focuses on the required skills and knowledge needed for building, running, and maintaining networks and prepares participants for various roles in the IT and cybersecurity sectors.

One of the main features of the OL-7822-06 course is its thorough curriculum, which covers key topics such as networking fundamentals, including OSI and TCP/IP models, IPv4 and IPv6 addressing, and subnetting. It dives deep into network protocols, ensuring learners acquire a firm grasp of how data flows across networks, as well as the role of routers and switches in maintaining efficient network operations.

The course also emphasizes hands-on learning, leveraging various simulation tools and virtual labs that provide students with real-world scenarios to apply their knowledge practically. These labs are integral in helping learners understand the configuration and troubleshooting of network devices, enhancing their problem-solving skills in a controlled environment.

Another significant aspect of OL-7822-06 is its focus on emerging technologies. The course introduces students to concepts such as network security, cloud computing, wireless networking, and IoT (Internet of Things). This inclusion reflects the ever-evolving landscape of technology and prepares participants to be adaptable in the face of rapid change within the industry.

Additionally, the OL-7822-06 course promotes collaboration and peer engagement through group projects and discussions. This not only fosters a sense of community among learners but also enhances their communication skills, which are essential in modern IT environments.

The course is structured to accommodate various learning styles, offering a blend of theoretical knowledge and practical exercises. It provides assessments and quizzes that help gauge understanding and retention of information, ensuring students are well-prepared for certification exams and real-world applications.

In summary, Cisco Systems OL-7822-06 stands out as a robust educational offering that combines foundational networking principles with advanced technologies. Its focus on hands-on experience, collaboration, and the introduction of current industry trends makes it an invaluable resource for aspiring networking professionals, ultimately paving the way for a successful career in the tech industry.
Top Page Image Contents