Cisco Systems OL-7822-06 quick start Examples

Page 44

Chapter 4 Connect the Management Interfaces and Perform Initial System Configuration

Perform the Initial System Configuration

Backing-up general configuration file...

Copy temporary file to final location...

Done!

Examples

EXAMPLE 1:, page 4-24

EXAMPLE 2:, page 4-24

EXAMPLE 3:, page 4-24

EXAMPLE 1:

Following is an example of a configuration that the user aborted due to errors detected in the configuration.

Note that no confirmation is requested for the decision to abort the setup. Had there been no errors, confirmation would have been requested before aborting.

Data collection for the system configuration is completed.

Would you like to view the new configuration before it is applied? [yes/no]: n

Found errors in the new configuration, would you like to view them? [yes]: y

The following errors were found:

Warning - RDR formatter destination 10.1.1.1 is not allowed in the IP access-class. Warning - default Gateway 10.1.1.1 is not allowed in the IP access-class.

Warning - IP Access list (1) conflicts with Telnet Access list (2) as follows: Access list 2 permits all addresses while Access list 1 denies it.

Apply and Save this configuration? [yes/no]: n

Setup procedure aborted, no configuration changes made.

EXAMPLE 2:

Following is an example of a configuration that was applied and saved to the startup configuration as well as to an FTP site.

Although not demonstrated in this example, it is recommended that you always view the configuration before applying it.

Data collection for the system configuration is completed.

Would you like to view the new configuration before it is applied? [yes/no]: Apply and Save this configuration? [yes/no]: y

(New configuration would be displayed here)

The running configuration would be overwritten by the changes you have just entered, are you sure? [yes/no]:y

The new running configuration will be saved to the startup configuration.

Do you want to save a copy of the startup configuration file in a remote station? [no]:y Enter a full FTP path of the remote destination: ftp://vk:vk@10.1.1.253/h:/copyofstartup.txt

Committing configuration...

Configuration completed successfully.

Saving configuration...

Writing general configuration file to temporary location...

Backing-up general configuration file...

Copy temporary file to final location...

Done!

EXAMPLE 3:

Following is an example of a configuration that was aborted, although no errors were detected.

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

4-24

OL-7822-06

 

 

Image 44
Contents Cisco Service Control Engine 1000 2xGBE Quick Start Guide Page N T E N T S Example Example 2 Installing a Service Control Application OL-7822-06 Information About Preparing for Installation Site Preparation and UnpackingTools and Parts Workbench or Tabletop InstallationPrepare for Rack-Mount Installation Prepare for Installation Workbench or Tabletop Installation OL-7822-06 Rack-Mount the SCE SCE 1000 Mounting BracketsAttach the Brackets to the SCE Attaching the Mounting Brackets 4-postInstalling the Crossrail Supports Four-post rack only Assemble the Crossrail SupportsMount the System to the Rack Attach the Crossrail Supports to the RackSummary Steps Securing the SCE Platform to the Rack Connect the Power Supply Units Connect the Chassis GroundConnecting the Power Grounding the Unit DCConnect the DC-Input Power Supply Unit Connecting the DC PowerConnect the AC-Input Power Supply Unit Connecting the AC PowerConnecting to the Local Console Connect the Local ConsolePerform the Initial System Configuration Initial System ConfigurationSetup Command Setup Command Parameters Parameter Definition Configuring Initial Settings ExampleConfiguring the Hostname Setting the PasswordsConfiguring Time Settings ExampleEnter time zone name UTC CET Configuring the DNS Settings Enter time interval in seconds between unicast updatesEnter Primary DNS IP address Configuring the RDR Formatter Destination Configuring Access Control Lists ACLsInitial IP address Wildcard bits Range Deny Permit any Examples Configuring Snmp Enter the Snmp configuration menu Type the trap manager community string and press press Enter Enter Snmp trap manager community string Configuring the Topology-Dependent Parameters About the Topology-Dependent ParametersExample 1, Example 2, Example 3, Completing and Saving the Configuration Apply and Save this configuration? yes/no Examples Connect the Management Interface ExampleOL-7822-06 Information About Cabling Single Link Inline TopologyBump-in-the-Wire Installation Single Link Receive-only TopologyConfigure GigabitEthernet Auto-Negotiation Cabling the Line InterfacesSCE Model Transceiver Transmit Power Receive Power Distance Connect the GBE Line Interface PortsCable the Line Ports Cabling the Line Interfaces OL-7822-06 Verifying Operational Status Examining the LEDsFinal Tests Viewing the User Log Counters Saving the Configuration Settings Following example shows the running configuration file ExamplesAdvanced Configuration of the SCE Platform Loading and Activating a Service Control ApplicationOL-7822-06 Troubleshoot Startup Problems SCE 1000 Operational StatusTroubleshoot Startup Problems SCE 1000 Operational Status Identifying Startup Problems CLI Commands for TroubleshootingTroubleshooting the link interface subsystem Page OL-7822-06

OL-7822-06 specifications

Cisco Systems OL-7822-06 is a comprehensive course offered within the Cisco Networking Academy, designed to equip students and professionals with a deep understanding of basic networking concepts and advanced networking technologies. This course primarily focuses on the required skills and knowledge needed for building, running, and maintaining networks and prepares participants for various roles in the IT and cybersecurity sectors.

One of the main features of the OL-7822-06 course is its thorough curriculum, which covers key topics such as networking fundamentals, including OSI and TCP/IP models, IPv4 and IPv6 addressing, and subnetting. It dives deep into network protocols, ensuring learners acquire a firm grasp of how data flows across networks, as well as the role of routers and switches in maintaining efficient network operations.

The course also emphasizes hands-on learning, leveraging various simulation tools and virtual labs that provide students with real-world scenarios to apply their knowledge practically. These labs are integral in helping learners understand the configuration and troubleshooting of network devices, enhancing their problem-solving skills in a controlled environment.

Another significant aspect of OL-7822-06 is its focus on emerging technologies. The course introduces students to concepts such as network security, cloud computing, wireless networking, and IoT (Internet of Things). This inclusion reflects the ever-evolving landscape of technology and prepares participants to be adaptable in the face of rapid change within the industry.

Additionally, the OL-7822-06 course promotes collaboration and peer engagement through group projects and discussions. This not only fosters a sense of community among learners but also enhances their communication skills, which are essential in modern IT environments.

The course is structured to accommodate various learning styles, offering a blend of theoretical knowledge and practical exercises. It provides assessments and quizzes that help gauge understanding and retention of information, ensuring students are well-prepared for certification exams and real-world applications.

In summary, Cisco Systems OL-7822-06 stands out as a robust educational offering that combines foundational networking principles with advanced technologies. Its focus on hands-on experience, collaboration, and the introduction of current industry trends makes it an invaluable resource for aspiring networking professionals, ultimately paving the way for a successful career in the tech industry.