Cisco Systems OL-7822-06 Cabling the Line Interfaces, Configure GigabitEthernet Auto-Negotiation

Page 49
running-configstartup-config

Chapter 5 Cable the Line Ports

Figure 5-2 External Splitting Topology

PWR A PWR B STATUS BYPASS

LINK RX

TX

LINK RX

TX

RX MM

TX

RX

MM

TX

 

 

GBE-1

 

 

SUB

LINE

NET

 

Cabling the Line Interfaces

Cisco SCE 1000 Series

2xGBE

210417

 

 

 

Router

Optical

Subscriber

splitter

 

 

 

 

Cabling the Line Interfaces

Configure GigabitEthernet Auto-Negotiation, page 5-3

Connect the GBE Line Interface Ports, page 5-4

Network

Router

Configure GigabitEthernet Auto-Negotiation

By default, the SCE 1000 GBE line interface ports are configured with auto-negotiation disabled.

Note If you change any parameters, you must save the new configuration settings. Type copy , and press Enter.

Step 1 At the SCE 1000# prompt, type configure and press press Enter.

Enters Global Configuration Mode.

Step 2 At the SCE 1000(config)# prompt, type interface GigabitEthernet 0/ portnumber, and press press Enter.

Enters the GigabitEthernet Interface configuration mode for the specified GBE port. portnumber is the number of the selected port (1 or 2).

Step 3 At the SCE 1000(config if)# prompt, type auto-negotiateand press press Enter.

Enables auto-negotiation for the GBE interface.

Step 4 At the SCE 1000(config if)# prompt, type exit and press press Enter.

Cisco Service Control Engine 1000 2xGBE Quick Start Guide

 

OL-7822-06

5-3

 

 

 

Image 49
Contents Cisco Service Control Engine 1000 2xGBE Quick Start Guide Page N T E N T S Example Example 2 Installing a Service Control Application OL-7822-06 Site Preparation and Unpacking Information About Preparing for InstallationPrepare for Rack-Mount Installation Workbench or Tabletop InstallationTools and Parts Prepare for Installation Workbench or Tabletop Installation OL-7822-06 SCE 1000 Mounting Brackets Rack-Mount the SCEAttaching the Mounting Brackets 4-post Attach the Brackets to the SCEAssemble the Crossrail Supports Installing the Crossrail Supports Four-post rack onlyAttach the Crossrail Supports to the Rack Mount the System to the RackSummary Steps Securing the SCE Platform to the Rack Connect the Chassis Ground Connect the Power Supply UnitsGrounding the Unit DC Connecting the PowerConnecting the DC Power Connect the DC-Input Power Supply UnitConnecting the AC Power Connect the AC-Input Power Supply UnitConnect the Local Console Connecting to the Local ConsoleInitial System Configuration Perform the Initial System ConfigurationSetup Command Setup Command Parameters Parameter Definition Example Configuring Initial SettingsSetting the Passwords Configuring the HostnameExample Configuring Time SettingsEnter time zone name UTC CET Enter time interval in seconds between unicast updates Configuring the DNS SettingsEnter Primary DNS IP address Configuring Access Control Lists ACLs Configuring the RDR Formatter DestinationInitial IP address Wildcard bits Range Deny Permit any Examples Configuring Snmp Enter the Snmp configuration menu Type the trap manager community string and press press Enter Enter Snmp trap manager community string About the Topology-Dependent Parameters Configuring the Topology-Dependent ParametersExample 1, Example 2, Example 3, Completing and Saving the Configuration Apply and Save this configuration? yes/no Examples Example Connect the Management InterfaceOL-7822-06 Single Link Inline Topology Information About CablingSingle Link Receive-only Topology Bump-in-the-Wire InstallationCabling the Line Interfaces Configure GigabitEthernet Auto-NegotiationConnect the GBE Line Interface Ports SCE Model Transceiver Transmit Power Receive Power DistanceCable the Line Ports Cabling the Line Interfaces OL-7822-06 Final Tests Examining the LEDsVerifying Operational Status Viewing the User Log Counters Saving the Configuration Settings Examples Following example shows the running configuration fileLoading and Activating a Service Control Application Advanced Configuration of the SCE PlatformOL-7822-06 SCE 1000 Operational Status Troubleshoot Startup ProblemsTroubleshoot Startup Problems SCE 1000 Operational Status CLI Commands for Troubleshooting Identifying Startup ProblemsTroubleshooting the link interface subsystem Page OL-7822-06

OL-7822-06 specifications

Cisco Systems OL-7822-06 is a comprehensive course offered within the Cisco Networking Academy, designed to equip students and professionals with a deep understanding of basic networking concepts and advanced networking technologies. This course primarily focuses on the required skills and knowledge needed for building, running, and maintaining networks and prepares participants for various roles in the IT and cybersecurity sectors.

One of the main features of the OL-7822-06 course is its thorough curriculum, which covers key topics such as networking fundamentals, including OSI and TCP/IP models, IPv4 and IPv6 addressing, and subnetting. It dives deep into network protocols, ensuring learners acquire a firm grasp of how data flows across networks, as well as the role of routers and switches in maintaining efficient network operations.

The course also emphasizes hands-on learning, leveraging various simulation tools and virtual labs that provide students with real-world scenarios to apply their knowledge practically. These labs are integral in helping learners understand the configuration and troubleshooting of network devices, enhancing their problem-solving skills in a controlled environment.

Another significant aspect of OL-7822-06 is its focus on emerging technologies. The course introduces students to concepts such as network security, cloud computing, wireless networking, and IoT (Internet of Things). This inclusion reflects the ever-evolving landscape of technology and prepares participants to be adaptable in the face of rapid change within the industry.

Additionally, the OL-7822-06 course promotes collaboration and peer engagement through group projects and discussions. This not only fosters a sense of community among learners but also enhances their communication skills, which are essential in modern IT environments.

The course is structured to accommodate various learning styles, offering a blend of theoretical knowledge and practical exercises. It provides assessments and quizzes that help gauge understanding and retention of information, ensuring students are well-prepared for certification exams and real-world applications.

In summary, Cisco Systems OL-7822-06 stands out as a robust educational offering that combines foundational networking principles with advanced technologies. Its focus on hands-on experience, collaboration, and the introduction of current industry trends makes it an invaluable resource for aspiring networking professionals, ultimately paving the way for a successful career in the tech industry.