Cisco Systems MGX-FRSM-HS2, MGX-FRSM-2CT3, MGX-FRSM-2T3E3 manual Cnfcdrscprtn 300 300

Page 13
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6

Using the CLI to Configure the Card, Lines, and Ports

On the CLI of the AUSM/B:

If necessary, modify the resource partitioning for the whole card by executing the cnfcdrscprtn command. You can view resource partitioning through dspcdrscprtn.

cnfcdrscprtn <number_PAR_conns number_PNNI_conns number_TAG_conns>

•number_PAR_conns is the number of connections in the range 0–1000 for PAR.

•number_PNNI_conns is the number of connections in the range 0–1000 for PNNI.

•number_TAG_conns is the number of connections in the range 0–1000 for MPLS. For example, you could reserve 300 connections for each controller on the AUSM with:

cnfcdrscprtn 300 300 300

Activate a physical line by using addln for each of the eight lines as needed: addln <line_number>

Optionally, use the cnfln command to specify line coding, line length, and clock source: cnfln <line_num> <line_code> <line_len> <clk_src> [E1-signaling]

Execute upport to activate the logical operation of the line: upport <port_number>, where port_number is in the range 1–8. If necessary, execute cnfportq to modify the egress queues:

cnfportq <port_num> <q_num> <q_algo> <q_depth> <clp_high> <clp_low> <efci_thres>

port_num is the logical port number in the range 1–8.

q_num is the queue number in the range 1–16. 0 is the default for addchan.

1=CBR

2=VBR

3=ABR

4=UBR

q_algo is a number to specify the queue algorithm:

0=disable queue

1=high priority—always serve 2=best available

3=minimum guaranteed bandwidth

4=minimum guaranteed bandwidth with maximum rate shaping 5=CBR with smoothing

q_depth is the maximum queue depth in the range 1–16000 cells.

clp_high is the high cell loss priority in the range 1–16000 cells.

clp_low is the low cell loss priority in the range 1–16000 cells.

efci_thres is the EFCI threshold in the range 1–16000 cells.

If necessary, configure resources at the port level by executing cnfportrscprtn. Use dspportrscprtn to see the current resource partitioning.

Card and Service Configuration 6-13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Modifying the Resource Partitioning Tasks for Configuring Cards and ServicesRules for Adding Connections Sequence of Configuration TasksRules for Adding Three-Segment Connections Rules for Adding a DAX ConnectionRules for Adding Management Connections Processor Switching Module Cnfcdrscprtn numberPARconns numberPNNIconns numberTAGconns Configuring Card-Level Parameters, Lines, and PortsAddport portnum linenum pctbw minvpi maxvpi Cnfatmln linenum type Automatic Protection Switching on the PXMProcessor Switching Module Cnfcon connID routepriority maxcost restricttrunktype CAC Adding Connections on a PXM in a Stand-Alone NodeCnfupcubr connID polType pcr0+1 cdvt0+1 IngPcUtil CLP Using the CLI to Configure the Card, Lines, and Ports ATM Universal Service ModuleCnfportq portnum qnum qalgo qdepth clphigh clplow efcithres Cnfcdrscprtn 300 300Adding and Configuring Connections on the AUSM/B Using the CLI to Configure Inverse MultiplexingAddimagrp groupnum porttype listoflinks minNumLink Porttype Is the port type 1=UNI, 2=NN1ConnID Default is slave, so you actually do not need to type aSlot number, port number, vci, and vpi of the slave end ATM Universal Service Module Adding and Configuring Connections on the AUSM/B Epdthreshold BPX 8600-to-BPX 8600 SegmentEfcithresh Is the Efci threshold in the range 1-16000 cells Types of Frame Service Modules Frame Service Module FeaturesVery High Speed Frame Service Modules IntroductionFour-Port Unchannelized Frame Service Module for Frame Service Module FeaturesMGX-FRSM-2T3E3 Features MGX-FRSM-2CT3 FeaturesMGX-FRSM-HS1/B Features MGX-FRSM-HS2/B FeaturesEight-Port Frsm Features Frame Relay-to-ATM Network Interworking Description of Connection Types on the FrsmCongestion Indication for NIW Connections PVC Status Management Frame Relay-to-ATM Service InterworkingCell Loss Priority Congestion Indication Frame Forwarding Command and Response MappingATM/Frame-to-User Network Interface Translation and Transparent ModesConfiguring the Frsm Cards, Lines, and Ports Configuring Frame Relay ServiceCnfln linenum linetype linerate Addport portnum linenum ds0speed beginslot numslot porttype Addport portnum linenum porttypeCnfport portnum lmisig asyn elmi T391 T392 N391 N392 N393 Addport portnum porttypeConfiguring Frame Relay Service Addred redPrimarySlotNum redSecondarySlotNum redType Adding a Frame Relay ConnectionConfiguring Frame Relay Service =NIW Cnfchanmap channum chanType FECN/EFCI DE to CLP CLP to DEEstablishing the BPX 8600-to-BPX 8600-Series Segment Test Commands for the FRSMsBit Error Rate Testing on an Unchannelized T3 or E3 Frsm Features Circuit Emulation Service Module for T3 and E3Cell Delay Treatment Error and Alarm Response Configuring Service on a T3 or E3 CesmAdding and Modifying Connections Configuring the Card, Lines, and PortsCnfcon portnum Cdvt CellLossIntegPeriod bufsize Addcon portnum mastership remoteConnIdBit Error Rate Testing on a T3 or E3 Cesm Structured Data Transfer Eight-Port Circuit Emulation Service ModulesUnstructured Data Transfer Error and Alarm Response Cell Delay TreatmentRedundancy Support for the Eight-Port Cesm Cnfln linenum linecode linelen clksrc E1-signaling Configuring Service on an Eight-Port CesmAddport portnum linenum beginslot numslot porttype Configuring Bulk Distribution and RedundancyAdding and Modifying Connections Eight-Port Circuit Emulation Service Modules Configuring Card and Line Parameters Service Resource ModuleRedundancy Support by the MGX-SRM-3T3/B Bulk Distribution for T1 ServiceTo specify 11 redundancy. Enter a 2 to specify 1 N Configuring Redundancy Through the Redundancy BusRedundancy . Only an SRM can support 1 N redundancy Configuring Redundancy Through the Distribution Bus Bit Error Rate Testing Through an MGX-SRM-3T3Card pair. Permissible slot numbers are in the range 11-14, 17-22,Bit Error Rate Testing Through an MGX-SRM-3T3 Pattern Test for AX-FRSM-8E1 and MGX-CESM-8E1 In-band/ESF Pattern Test OptionsLoopback Test Options

MGX-FRSM-HS2, MGX-FRSM-2T3E3, MGX-FRSM-2CT3 specifications

Cisco Systems is a leader in networking technology and infrastructure, providing solutions that drive innovation and efficiency for businesses worldwide. Among its diverse range of products, the MGX series stands out as a pivotal component for the network-centric era, especially with models like MGX-FRSM-2CT3, MGX-FRSM-2T3E3, and MGX-FRSM-HS2. These modules are primarily designed for the MGX 8800 series routers, facilitating efficient traffic management and service delivery.

The MGX-FRSM-2CT3 is a versatile module that supports two T3 connections. It allows network operators to seamlessly integrate high-capacity circuit-switched and packet-switched data on a unified platform. This versatility is crucial for service providers looking to enhance their bandwidth offerings while ensuring reliable performance across voice, video, and data applications.

In contrast, the MGX-FRSM-2T3E3 module caters to operators needing E3 support. This feature allows for efficient data transport over a broader bandwidth, catering to European standards. The E3 configuration is vital for service providers operating in Europe or regions that utilize E3 technology prominently.

The MGX-FRSM-HS2 module is another significant offering, designed to accommodate the increasing demand for high speed and high capacity. It supports higher-order TDM and packet technologies, enabling operators to implement advanced services such as VoIP, video conferencing, and other data-intensive applications. This module provides scalability and reliability, making it ideal for next-generation networks.

All three modules leverage Cisco’s advanced switching and routing technology, ensuring optimal performance and minimal latency. The integration of Quality of Service (QoS) features allows network administrators to prioritize traffic types effectively, ensuring mission-critical applications receive the necessary bandwidth.

Additionally, these MGX modules support various signaling protocols, enabling interoperability with existing network infrastructure while also facilitating the migration to newer technologies. They play an essential role in modernizing telecom networks, allowing service providers to adapt to changing market demands and technology landscapes.

In summary, the Cisco MGX-FRSM-2CT3, MGX-FRSM-2T3E3, and MGX-FRSM-HS2 modules are key components for businesses looking to enhance their networking capabilities. With their robust support for T3 and E3 technologies, high scalability, and advanced QoS features, these modules empower service providers to deliver a wide range of services, drive innovation, and meet the growing demands of users in an increasingly connected world.
Top Page Image Contents