Cisco Systems MGX-FRSM-2T3E3, MGX-FRSM-2CT3 manual Eight-Port Circuit Emulation Service Modules

Page 41

Eight-Port Circuit Emulation Service Modules

Eight-Port Circuit Emulation Service Modules

The main function of the Circuit Emulation Service Module (CESM) is to provide a constant bit rate (CBR) circuit emulation service by converting data streams into CBR AAL1 cells for transport across an ATM network. The CESM supports the CES-IS specifications of the ATM Forum.

The eight-port CESM lets you configure individual physical ports for structured or unstructured data transfer. The card sets consist of an MGX-CESM-8T1 or MGX-CESM-8E1 front card and one of the following back cards:

•

•

•

•

•

RJ48-8T1

R-RJ48-8T1 for supporting 1:N redundancy through the optional MGX-SRM-3T3

RJ48-8E1

R-RJ48-8E1 for supporting 1:N redundancy through the optional MGX-SRM-3T3

SMB-8E1

Structured Data Transfer

If you configure an individual port for structured data transfer, the eight-port CESM supports:

•Synchronous timing.

•Superframe or Extended Superframe for T1.

•N x 64 Kbps, fractional DS1/E1 service (contiguous time slots only). You can map an N x 64-Kbps channel to any VC.

•CAS robbed bit for T1 (ABCD for ESF and SF frames) and CAS for E1 (channel 16).

•CCS channel as a transparent data channel.

•A choice of partial-fill payload sizes.

•Idle detection and suppression for 64-Kbps CAS connections.

•Loopback diagnostics on a line or a connection (addlnloop, tstcon, and tstdelay commands).

•Bit error rate test (BERT) functionality with loopback pattern generation and verification on individual lines or logical port. For a description of the BERT functions, see the section titled “Bit Error Rate Testing Through an MGX-SRM-3T3.”

Unstructured Data Transfer

If you configure an individual port for unstructured data transfer, the eight-port CESM supports:

•Synchronous or asynchronous timing at T1 (1.544 Mbps) or E1 (2.048 Mbps) rates. For asynchronous timing, you can select its basis as either SRTS and adaptive clock recovery.

•The special port type framingOnVcDisconnect. This port type prevents a remote-end CPE from going to LOF by placing a line in remote loopback mode when the CESM determines that a connection deletion or suspension occurred at the network-side ATM interface.

•Ability to detect and display a yellow alarm for the ESF framing on a T1 line.

•Loopback diagnostics on a line or a connection (addlnloop, tstcon, and tstdelay commands).

•Bit error rate test (BERT) functionality with loopback pattern generation and verification on individual lines. For a description of BERT functions, see the section “Bit Error Rate Testing Through an MGX-SRM-3T3.”

Card and Service Configuration 6-41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Modifying the Resource Partitioning Tasks for Configuring Cards and ServicesRules for Adding Connections Sequence of Configuration TasksRules for Adding Three-Segment Connections Rules for Adding a DAX ConnectionRules for Adding Management Connections Processor Switching Module Addport portnum linenum pctbw minvpi maxvpi Configuring Card-Level Parameters, Lines, and PortsCnfcdrscprtn numberPARconns numberPNNIconns numberTAGconns Cnfatmln linenum type Automatic Protection Switching on the PXMProcessor Switching Module Cnfcon connID routepriority maxcost restricttrunktype CAC Adding Connections on a PXM in a Stand-Alone NodeCnfupcubr connID polType pcr0+1 cdvt0+1 IngPcUtil CLP Using the CLI to Configure the Card, Lines, and Ports ATM Universal Service ModuleCnfportq portnum qnum qalgo qdepth clphigh clplow efcithres Cnfcdrscprtn 300 300Adding and Configuring Connections on the AUSM/B Using the CLI to Configure Inverse MultiplexingAddimagrp groupnum porttype listoflinks minNumLink Porttype Is the port type 1=UNI, 2=NN1Slot number, port number, vci, and vpi of the slave end Default is slave, so you actually do not need to type aConnID ATM Universal Service Module Adding and Configuring Connections on the AUSM/B Efcithresh Is the Efci threshold in the range 1-16000 cells BPX 8600-to-BPX 8600 SegmentEpdthreshold Types of Frame Service Modules Frame Service Module FeaturesVery High Speed Frame Service Modules IntroductionFour-Port Unchannelized Frame Service Module for Frame Service Module FeaturesMGX-FRSM-2T3E3 Features MGX-FRSM-2CT3 FeaturesEight-Port Frsm Features MGX-FRSM-HS2/B FeaturesMGX-FRSM-HS1/B Features Congestion Indication for NIW Connections Description of Connection Types on the FrsmFrame Relay-to-ATM Network Interworking Cell Loss Priority Frame Relay-to-ATM Service InterworkingPVC Status Management Congestion Indication Frame Forwarding Command and Response MappingATM/Frame-to-User Network Interface Translation and Transparent ModesCnfln linenum linetype linerate Configuring Frame Relay ServiceConfiguring the Frsm Cards, Lines, and Ports Addport portnum linenum ds0speed beginslot numslot porttype Addport portnum linenum porttypeCnfport portnum lmisig asyn elmi T391 T392 N391 N392 N393 Addport portnum porttypeConfiguring Frame Relay Service Addred redPrimarySlotNum redSecondarySlotNum redType Adding a Frame Relay ConnectionConfiguring Frame Relay Service =NIW Cnfchanmap channum chanType FECN/EFCI DE to CLP CLP to DEEstablishing the BPX 8600-to-BPX 8600-Series Segment Test Commands for the FRSMsBit Error Rate Testing on an Unchannelized T3 or E3 Frsm Cell Delay Treatment Circuit Emulation Service Module for T3 and E3Features Error and Alarm Response Configuring Service on a T3 or E3 CesmAdding and Modifying Connections Configuring the Card, Lines, and PortsCnfcon portnum Cdvt CellLossIntegPeriod bufsize Addcon portnum mastership remoteConnIdBit Error Rate Testing on a T3 or E3 Cesm Unstructured Data Transfer Eight-Port Circuit Emulation Service ModulesStructured Data Transfer Redundancy Support for the Eight-Port Cesm Cell Delay TreatmentError and Alarm Response Cnfln linenum linecode linelen clksrc E1-signaling Configuring Service on an Eight-Port CesmAddport portnum linenum beginslot numslot porttype Configuring Bulk Distribution and RedundancyAdding and Modifying Connections Eight-Port Circuit Emulation Service Modules Configuring Card and Line Parameters Service Resource ModuleRedundancy Support by the MGX-SRM-3T3/B Bulk Distribution for T1 ServiceRedundancy . Only an SRM can support 1 N redundancy Configuring Redundancy Through the Redundancy BusTo specify 11 redundancy. Enter a 2 to specify 1 N Configuring Redundancy Through the Distribution Bus Bit Error Rate Testing Through an MGX-SRM-3T3Card pair. Permissible slot numbers are in the range 11-14, 17-22,Bit Error Rate Testing Through an MGX-SRM-3T3 Pattern Test for AX-FRSM-8E1 and MGX-CESM-8E1 In-band/ESF Pattern Test OptionsLoopback Test Options

MGX-FRSM-HS2, MGX-FRSM-2T3E3, MGX-FRSM-2CT3 specifications

Cisco Systems is a leader in networking technology and infrastructure, providing solutions that drive innovation and efficiency for businesses worldwide. Among its diverse range of products, the MGX series stands out as a pivotal component for the network-centric era, especially with models like MGX-FRSM-2CT3, MGX-FRSM-2T3E3, and MGX-FRSM-HS2. These modules are primarily designed for the MGX 8800 series routers, facilitating efficient traffic management and service delivery.

The MGX-FRSM-2CT3 is a versatile module that supports two T3 connections. It allows network operators to seamlessly integrate high-capacity circuit-switched and packet-switched data on a unified platform. This versatility is crucial for service providers looking to enhance their bandwidth offerings while ensuring reliable performance across voice, video, and data applications.

In contrast, the MGX-FRSM-2T3E3 module caters to operators needing E3 support. This feature allows for efficient data transport over a broader bandwidth, catering to European standards. The E3 configuration is vital for service providers operating in Europe or regions that utilize E3 technology prominently.

The MGX-FRSM-HS2 module is another significant offering, designed to accommodate the increasing demand for high speed and high capacity. It supports higher-order TDM and packet technologies, enabling operators to implement advanced services such as VoIP, video conferencing, and other data-intensive applications. This module provides scalability and reliability, making it ideal for next-generation networks.

All three modules leverage Cisco’s advanced switching and routing technology, ensuring optimal performance and minimal latency. The integration of Quality of Service (QoS) features allows network administrators to prioritize traffic types effectively, ensuring mission-critical applications receive the necessary bandwidth.

Additionally, these MGX modules support various signaling protocols, enabling interoperability with existing network infrastructure while also facilitating the migration to newer technologies. They play an essential role in modernizing telecom networks, allowing service providers to adapt to changing market demands and technology landscapes.

In summary, the Cisco MGX-FRSM-2CT3, MGX-FRSM-2T3E3, and MGX-FRSM-HS2 modules are key components for businesses looking to enhance their networking capabilities. With their robust support for T3 and E3 technologies, high scalability, and advanced QoS features, these modules empower service providers to deliver a wide range of services, drive innovation, and meet the growing demands of users in an increasingly connected world.
Top Page Image Contents