Cisco Systems MGX-FRSM-2CT3, MGX-FRSM-HS2 manual Adding Connections on a PXM in a Stand-Alone Node

Page 9

Adding Connections on a PXM in a Stand-Alone Node

Adding Connections on a PXM in a Stand-Alone Node

This section describes the CLI commands for provisioning connections on a PXM in a stand-alone node. Connection addition abides by the rules for a standard connection or a management connection in the form of either a three-segment connection or a DAX con. See “Rules for Adding Connections” earlier in this chapter. In addition this section describes the commands for modifying certain features for a connection and policing connections by way of usage parameter control.

The CLI commands correspond to functions in the Cisco WAN Manager application. The preferred CLI command is addcon. (If the application requires NSAP addressing, use addchan to add the connection and cnfchan if you need to modify it. Refer to the command reference for the syntax.) In addition, On the PXM CLI:

Step 1 Execute the addcon command according to the following syntax:

addcon <port_num> <conn_type> <local_VPI> <local_VCI> <service> [CAC] [mastership] [remoteConnId]

•port_no is the logical port in the range 1–32 for a user connection or 34 for management connection.

•conn_type is a number identifying the connection type—1 for VPC or 2 for VCC.

•local_VPI is the local VPI in the range 0–4095.

•local_VCI is the local VCI in the range 0–65535.

•service is a number in the range 1–4 to specify the type of service: 1=CBR, 2=VBR, 3=ABR, and 4=UBR.

•CAC optionally lets you turn off the addition of the loading affect of a connection to the aggregated load on a port.

•mastership specifies whether the endpoint you are adding is the master or slave. 1=master. 2=slave (default). The syntax shows this parameter as optional because you need to enter it at only the master end. Slave is the default, so you do not explicitly need to specify it when entering a DAX con.

•remoteConnId identifies the connection at the slave end. The format for remoteConnId is Remote_nodename.slot_num.remote_VPI.remoteVCI. Note that the slot number of the active PXM is always 0 when you add a connection because the PXM slot number is a fixed, logical value.

Step 2 If necessary, modify a connection by using cnfcon:

cnfcon <conn_ID> <route_priority> <max_cost> <restrict_trunk_type> [CAC]

•conn_ID identifies the connection. The format is logical_port.VPI.VCI.

•route_priority is the priority of the connection for re-routing. The range is 1–15 and is meaningful only in relation to the priority of other connections.

•max_cost is a number establishing the maximum cost of the connection route. The range is 1–255 and is meaningful only in relation to the cost of other connections for which you specify a maximum cost.

•restrict_trunk_type is a number that specifies the type of trunk this connection can traverse. The numbers are 1 for no restriction, 2 for terrestrial trunk only, and 3 for satellite trunk only.

•CAC optionally lets you turn on or off the addition of the loading affect of a connection to the aggregated load on a port.

Card and Service Configuration 6-9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Modifying the Resource Partitioning Tasks for Configuring Cards and ServicesRules for Adding Connections Sequence of Configuration TasksRules for Adding Three-Segment Connections Rules for Adding a DAX ConnectionRules for Adding Management Connections Processor Switching Module Configuring Card-Level Parameters, Lines, and Ports Cnfcdrscprtn numberPARconns numberPNNIconns numberTAGconnsAddport portnum linenum pctbw minvpi maxvpi Cnfatmln linenum type Automatic Protection Switching on the PXMProcessor Switching Module Cnfcon connID routepriority maxcost restricttrunktype CAC Adding Connections on a PXM in a Stand-Alone NodeCnfupcubr connID polType pcr0+1 cdvt0+1 IngPcUtil CLP Using the CLI to Configure the Card, Lines, and Ports ATM Universal Service ModuleCnfportq portnum qnum qalgo qdepth clphigh clplow efcithres Cnfcdrscprtn 300 300Adding and Configuring Connections on the AUSM/B Using the CLI to Configure Inverse MultiplexingAddimagrp groupnum porttype listoflinks minNumLink Porttype Is the port type 1=UNI, 2=NN1Default is slave, so you actually do not need to type a ConnIDSlot number, port number, vci, and vpi of the slave end ATM Universal Service Module Adding and Configuring Connections on the AUSM/B BPX 8600-to-BPX 8600 Segment EpdthresholdEfcithresh Is the Efci threshold in the range 1-16000 cells Types of Frame Service Modules Frame Service Module FeaturesVery High Speed Frame Service Modules IntroductionFour-Port Unchannelized Frame Service Module for Frame Service Module FeaturesMGX-FRSM-2T3E3 Features MGX-FRSM-2CT3 FeaturesMGX-FRSM-HS2/B Features MGX-FRSM-HS1/B FeaturesEight-Port Frsm Features Description of Connection Types on the Frsm Frame Relay-to-ATM Network InterworkingCongestion Indication for NIW Connections Frame Relay-to-ATM Service Interworking PVC Status ManagementCell Loss Priority Congestion Indication Frame Forwarding Command and Response MappingATM/Frame-to-User Network Interface Translation and Transparent ModesConfiguring Frame Relay Service Configuring the Frsm Cards, Lines, and PortsCnfln linenum linetype linerate Addport portnum linenum ds0speed beginslot numslot porttype Addport portnum linenum porttypeCnfport portnum lmisig asyn elmi T391 T392 N391 N392 N393 Addport portnum porttypeConfiguring Frame Relay Service Addred redPrimarySlotNum redSecondarySlotNum redType Adding a Frame Relay ConnectionConfiguring Frame Relay Service =NIW Cnfchanmap channum chanType FECN/EFCI DE to CLP CLP to DEEstablishing the BPX 8600-to-BPX 8600-Series Segment Test Commands for the FRSMsBit Error Rate Testing on an Unchannelized T3 or E3 Frsm Circuit Emulation Service Module for T3 and E3 FeaturesCell Delay Treatment Error and Alarm Response Configuring Service on a T3 or E3 CesmAdding and Modifying Connections Configuring the Card, Lines, and PortsCnfcon portnum Cdvt CellLossIntegPeriod bufsize Addcon portnum mastership remoteConnIdBit Error Rate Testing on a T3 or E3 Cesm Eight-Port Circuit Emulation Service Modules Structured Data TransferUnstructured Data Transfer Cell Delay Treatment Error and Alarm ResponseRedundancy Support for the Eight-Port Cesm Cnfln linenum linecode linelen clksrc E1-signaling Configuring Service on an Eight-Port CesmAddport portnum linenum beginslot numslot porttype Configuring Bulk Distribution and RedundancyAdding and Modifying Connections Eight-Port Circuit Emulation Service Modules Configuring Card and Line Parameters Service Resource ModuleRedundancy Support by the MGX-SRM-3T3/B Bulk Distribution for T1 ServiceConfiguring Redundancy Through the Redundancy Bus To specify 11 redundancy. Enter a 2 to specify 1 NRedundancy . Only an SRM can support 1 N redundancy Configuring Redundancy Through the Distribution Bus Bit Error Rate Testing Through an MGX-SRM-3T3Card pair. Permissible slot numbers are in the range 11-14, 17-22,Bit Error Rate Testing Through an MGX-SRM-3T3 Pattern Test for AX-FRSM-8E1 and MGX-CESM-8E1 In-band/ESF Pattern Test OptionsLoopback Test Options

MGX-FRSM-HS2, MGX-FRSM-2T3E3, MGX-FRSM-2CT3 specifications

Cisco Systems is a leader in networking technology and infrastructure, providing solutions that drive innovation and efficiency for businesses worldwide. Among its diverse range of products, the MGX series stands out as a pivotal component for the network-centric era, especially with models like MGX-FRSM-2CT3, MGX-FRSM-2T3E3, and MGX-FRSM-HS2. These modules are primarily designed for the MGX 8800 series routers, facilitating efficient traffic management and service delivery.

The MGX-FRSM-2CT3 is a versatile module that supports two T3 connections. It allows network operators to seamlessly integrate high-capacity circuit-switched and packet-switched data on a unified platform. This versatility is crucial for service providers looking to enhance their bandwidth offerings while ensuring reliable performance across voice, video, and data applications.

In contrast, the MGX-FRSM-2T3E3 module caters to operators needing E3 support. This feature allows for efficient data transport over a broader bandwidth, catering to European standards. The E3 configuration is vital for service providers operating in Europe or regions that utilize E3 technology prominently.

The MGX-FRSM-HS2 module is another significant offering, designed to accommodate the increasing demand for high speed and high capacity. It supports higher-order TDM and packet technologies, enabling operators to implement advanced services such as VoIP, video conferencing, and other data-intensive applications. This module provides scalability and reliability, making it ideal for next-generation networks.

All three modules leverage Cisco’s advanced switching and routing technology, ensuring optimal performance and minimal latency. The integration of Quality of Service (QoS) features allows network administrators to prioritize traffic types effectively, ensuring mission-critical applications receive the necessary bandwidth.

Additionally, these MGX modules support various signaling protocols, enabling interoperability with existing network infrastructure while also facilitating the migration to newer technologies. They play an essential role in modernizing telecom networks, allowing service providers to adapt to changing market demands and technology landscapes.

In summary, the Cisco MGX-FRSM-2CT3, MGX-FRSM-2T3E3, and MGX-FRSM-HS2 modules are key components for businesses looking to enhance their networking capabilities. With their robust support for T3 and E3 technologies, high scalability, and advanced QoS features, these modules empower service providers to deliver a wide range of services, drive innovation, and meet the growing demands of users in an increasingly connected world.
Top Page Image Contents