Cisco Systems SOHO 71 manual Connecting a Hub

Page 31

Chapter 2 Installation

Installing Your Router

Connecting a Hub

Before connecting a hub to the router, see Table 2-2for information on setting the TO HUB/TO PC button. To connect a hub, follow the steps in Figure 2-1. (Figure 2-1shows a Cisco 806 router, but the process is the same for a SOHO 71 router.)

Figure 2-1 Connecting a Hub

1. Set TO HUB/TO PC button.

Cisco 806 router

	TO HUB ETHERNET	10BASET
2. Connect yellow cable	TO PC	10BASET	COMPUTERS (E0)
			COMPUTERS (E0)
	4	3	2
to ETHERNET port 4			1
to ETHERNET port 4
on Cisco 806 router.

Model Cisco	806
CONSOLE

ETHERNET 10BASET	+5 VDC
	+5 VDC
INTERNET (E1)

Cisco 1528 Micro Hub 10/100

1X

2X

ETHERNET

3X

4X

SPEED

LED

1

100BaseTX

SOLID

2

3

4

10BaseT

BLINK

5

6

7

8

5X

6X

7X

8X

MDI

MDI-X

3.Connect other end of cable to hub.

4.If applicable, check setting of hub equivalent of router

TO HUB/TO PC.

51815

To verify your hub connection, ensure that the COMPUTERS 4 LED on the front panel is on after you have connected all cables and turned the router on. If the LED does not turn on, see Table 3-2in Chapter 3 for troubleshooting information.

Note Leave PCs attached to the hub turned off until you have completed router installation.

		Cisco 806 Router and SOHO 71 Router Hardware Installation Guide

	78-10432-04			2-7
	78-10432-04			2-7

Image 31

Contents Corporate Headquarters Page Copyright 2005 Cisco Systems, Inc. All rights reserved Page N T E N T S Installation Vii Viii Organization AudienceConventions Related Documentation Cisco.com Obtaining DocumentationDocumentation DVD Ordering Documentation Documentation FeedbackCisco Product Security Overview Reporting Security Problems in Cisco ProductsCisco Technical Support Website Obtaining Technical AssistanceSubmitting a Service Request Obtaining Additional Publications and Information Definitions of Service Request SeverityXviii Feature Routers Description FeaturesRouter LAN Ethernet Ports WAN Ethernet Port Console Port Router OverviewBack Panel Front Panel4shows the back panel of the Soho 71 router Color Function LEDsProduct Overview Router Overview Safety Preparing for InstallationBefore installing the router, read the following warnings Preventing Electrostatic Discharge Damage Unpacking the Box Preventing Router Damage Installing Your RouterConnected to Router Setting Router Port Type Button Setting Connecting Ethernet DevicesNetwork Device Router Button Ethernet Cable Connecting a Hub Connecting a Server, PC, or Workstation Connecting a Broadband Modem Connecting to the InternetConnecting an Ethernet Switch Connecting a Terminal or PC to the Console PortConnecting a Terminal or PC Connecting the AC AdapterVerifying Router Operation Connecting the AC adapterMounting Your Router Power/Link LEDs to Check Normal PatternsMounting on Wall Mounting on TableInstallation Mounting Your Router Mounting Router on Wall Starting the Crws Software Connecting to a WebsiteInstallation What to Do If You Cannot Connect to a Website Before You Call Your Cisco Reseller TroubleshootingSymptom Problem Solutions Problems During Initial Startup, Installation Problems After Router Is RunningTroubleshooting Problems After Router Is Running Description Design Specification Physical Dimensions System SpecificationsEnvironmental Operating Ranges Description Design Specification Router Power Port Connector PinoutsLaws and regulations Pin Function Function To HUB/TO PC Button Pin Position OUT PositionEthernet Cable Specifications Cabling SpecificationsType Category Shielding Maximum Cable DistanceCable Maximum Distance Chapter a Specifications and Cables Cabling Specifications Numerics IN-2 IN-3 IN-4