Billion Electric Company 400G manual Adsl Mode

Page 43

Billion 400G Router

ADSL Mode

Connect Mode: This mode will automatically detect your ADSL line mode, ADSL2+, ADSL2, G.dmt, G.lite, T1.413, AnnexM2 or AnnexM2+. But in some areas, multimode cannot detect the ADSL line mode very well. If it is the case, please adjust the ADSL line code to G.dmt first. If it still fails, please check with your ISP for line connection information.

Modulation: It will automatically detect capability of your ADSL line mode. Please keep the factory settings unless ADSL is detected as the symptom of a synchronization problem.

Profile Type: The profile type should be left in the default settings unless the ADSL mode is determined as the symptom of low link rate or instability problems. If such a problem is encountered, the profile setting may need to be changed to conform to the different DSLAM in the area.

Activate Line: Select false and then select true to activate any new Connect Mode settings.

Coding Gain: This reduces the router’s transmit power and will effect to router’s downstream performance. General, the higher the gain, the higher the downstream rate, but sometimes a gain that is too high will cause an unstable ADSL connection. The configurable ADSL coding gain is from 0 dB to 7dB, or automatic.

40

Chapter 4: Configuration

Image 43

Contents Page Table of Contents Table of Contents Introduction to your Router FeaturesRich Packet Filtering Dynamic Host Configuration Protocol Dhcp Client and ServerFirmware Upgradeable Virtual Server port forwardingPackage Contents Important note for using this routerInternet Power LAN Port 1XWireless Mail Front LEDsRear Ports 1X 4X RJ-45 connectorAntenna Cabling Basic Installation Connecting Your Router Select Internet Protocol TCP/IP and click Properties. See Double-clickLocal Area Connection. See FigureConfiguring PCs in Windows Then select the DNS Configuration tab. See Figure Configuring PC in Windows 95/98/MESelect TCP/IP Protocol and click Properties. See Figure Go to Start / Settings / Control Panel. In the Control PanelFactory Default Settings PPPoA Information from your ISP14 User name & Password Prompt Window Configuring with your Web BrowserStatus Quick Start ConfigurationAdsl Status StatusARP Table Routing Table Dhcp TableRouting Table Leased TableUPnP Portmap NAT SessionsEmail Status Diagnostic Error LogEvent Log Quick Start Billion 400G Router Billion 400G Router LAN Local Area Network ConfigurationBridge Interface IP Alias EthernetPrimary IP Address Ethernet Client Filter Ethernet Client Filter Default setting is set Disable→ Active PC in LAN Parameters WirelessWireless Distribution System WDS WPA-PSK / WPA2-PSK / WEP Wireless SecurityWEP Wireless Client Filter Default setting is set to Disable Wireless Client / MAC Address FilterAssociated Wireless Clients WPS Port SettingDhcp Server WAN Profile WAN Wide Area NetworkConnection PPPoA Connection Billion 400G Router MPoA Connection IPoA Routed Connection All PPPoE Pure BridgeAdsl Mode Time Zone SystemFirmware Upgrade Remote AccessBackup / Restore User Management Restart RouterBillion 400G Router Firewall and Access Control This with caution when connecting over the WAN General SettingsChanged Packet Filter Example Predefined Port Filters Rules Packet Filter Add TCP/UDP Filter Packet Filter Add Raw IP Filter Billion 400G Router Configuring Packet Filter Example Block Duration Intrusion DetectionBillion 400G Router Type of Block Drop Packet Duration Intrusion Name Detect Parameter BlacklistShow Log URL Filter Billion 400G Router Peer to Peer Blocking The default is set to Disabled Instant Message Blocking The default is set to DisabledIM / P2P Blocking High QoS Quality of ServiceFirewall Log PrioritizationDscp Mapping Table Wireless Adsl Router Standard DscpOutbound IP Throttling LAN to WAN Inbound IP Throttling WAN to LAN Information and Settings Connection DiagramMission-critical application Restricted Application Billion 400G Router Add Virtual Server Virtual Server known as Port ForwardingBillion 400G Router Example Add Click it to apply your settingsEdit DMZ Host Go to ConfigurationVirtual ServerEdit DMZ HostEdit One-to-One NAT Network Address Translation Go to ConfigurationVirtual ServerEdit One-to-one NATGlobal IP Address Well-known and registered Ports Port NumberProtocol Description Time Schedule Edit a Time Slot Configuration of Time ScheduleDelete a Time Slot Advanced Go to Configuration/Advanced/Static RouteStatic Route Dynamic DNS Dynamic DNSCheck Email Check EmailDevice Management Snmp V1 Universal Plug and Play UPnPFrom RFC 1213 MIB-II From RFC 1472 PPP/Security MIB From RFC1650 EtherLike-MIBFrom RFC 1493 Bridge MIB From RFC 1471 PPP/LCP MIBLogout DisableVlan Bridge Problems with the WAN Interface Problems starting up the routerProblems with the LAN Interface Contact SizweBroadband for Router Support Contact Telkom Adsl support