Cabletron Systems 3T02-04 manual Displaying Port Status

Page 31

Displaying Port Status

•RX_Q Overflows - number of incoming packets dropped by the port due to a lack of buffers. This entry shows status only; it is not selectable. After a reboot, the ATX tries to automatically re-allocate the Small Buffers among the ports so that the total number of RX_Q Overflows is minimized.

•Ring State - either opened, closed, or ring failure. This entry shows status only; it is not selectable.

•Ring Status - normally No Problems Detected. This entry shows status only; it is not selectable. If there are ring problems, one of the following will be displayed:

-Ring Recovery - This could be a normal state, indicating that a new station has just inserted into the ring and temporarily broken it. The ring should be back to normal in seconds. If it is not, check for stuck relays on a passive MAU, DB9 connectors plugged into the video port, mismatched ring speed (some stations at 4, some at 16), or poor wiring or connections.

-Single Station - The module’s Token Ring port is the only station it sees on the ring.

-Auto Removal - There is a serious problem with the connection, which resulted in the Token Ring port removing itself from the ring. Check the conditions listed under Ring Recovery.

-Lobe Wire Fault - The cable between the ATX and the MAU is defective causing the loopback test to fail. Therefore, the Token Ring port isn’t inserted into the ring.

-Soft Error - Historically indicates that an error has occurred. This can be caused by inserting a new station into the ring. Since this value represents a historical set, it may not necessarily indicate a current error condition.

-Hard Error - This frequently occurs when a new station is inserted into the ring; it can be ignored.

-Transmitting Beaconing - As state similar to Ring Recovery. Follow the guidelines above.

-Signal Loss - The Token Ring port is unable to communicate with the ring.

Token Ring Switch Module User Guide

Page 4-3

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Token Ring Switch Module Page Token Ring Switch Module User Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents Chapter Introduction Document Conventions Getting Help Related ManualsGeneral Description Standards ConnectorsLEDs POWER-UP LED Sequence Chapter Connecting to the NetworkIntroduction Connecting the Token Ring Module to a HUB Typical ConfigurationsUnshielded Twisted Pair Shielded Twisted Pair Connecting a Token Ring Module to a UTP HubConnecting a Token Ring Module to an STP MAU Chapter Configuring LCM Commands Connecting the LCMConfiguring the Bridging Type Setting the Ring SpeedTransparent Bridging Method Source Routing and SRTSegment Number Translation Options Bridge NumberARP Translation IPX Translation Source Routing ARP TranslationAppleTalk Translation ATX translate 4-6 apple on Configuring Token Ring Switch Module User Guide Displaying Port Status Chapter StatisticsStatistics Displaying Port Status Destination Addresses and Forwarding Outcomes Module StatisticsModule Statistics Statistics Token Ring Switch Module User Guide POWER-UP Diagnostics Chapter Diagnostics and TroubleshootingPower-up Tests Operational Diagnostics Power-up ResultsLoopback Tests Troubleshooting Diagnostic ResultsIf the Module Fails to Power Up Connectivity Problems Adding a Token Ring Switch Module Unpacking the Token Ring Switch ModuleChapter ADDING/SWAPPING Modules Adding/Swapping Modules Swapping a Module Token Ring Switch Module User Guide TCP/IP IPX Appendix a Technical SpecificationsDB9 for STP RJ45 for UTP Overview Appendix B Bridging MethodsAppendix B Bridging Methods Transparent BridgingFigure B-1 Source Routing Example Source Routing BridgingB-4 Token Ring Switch Module User Guide Source Routing Transparent Bridging B-6 Token Ring Switch Module User Guide ATX IndexIndex Index-2 Token Ring Switch Module User Guide

3T02-04 specifications

Cabletron Systems, a notable name in the networking industry, gained prominence for its pioneering products and innovative technologies. One of its formidable offerings is the Cabletron Systems 3T02-04, an advanced network switching device designed to cater to the evolving demands of high-performance networking environments.

The Cabletron Systems 3T02-04 excels in facilitating seamless data transfer within various network infrastructures. At its core, this device is engineered with key features that enhance its performance and adaptability. With a robust switching architecture, it provides high throughput and low latency, ensuring efficient handling of data traffic. This is particularly crucial for organizations that rely on rapid communication and data exchange for their operations.

One of the defining characteristics of the 3T02-04 is its multi-port configuration, which allows multiple devices to connect simultaneously. This enables the device to support a wide range of applications, from standard office networking to intensive data center operations. Equip with support for various data transmission protocols, including Ethernet, the 3T02-04 is highly versatile, meeting the diverse needs of modern networking tasks.

Additionally, Cabletron Systems incorporated advanced technologies such as Virtual LAN (VLAN) support in the 3T02-04, enhancing network segmentation and improving security measures. This feature allows network administrators to partition the network into different segments, ensuring that sensitive data remains separate and secure from other less critical services.

The 3T02-04 is also notable for its scalability. As organizations grow and their networking requirements evolve, the 3T02-04 can adapt. This scalability is crucial for businesses looking to future-proof their infrastructure investments, allowing them to add bandwidth and enhance connectivity without a complete overhaul of their existing systems.

Moreover, the robustness and reliability of the device ensure that it can withstand the rigors of demanding environments. Its durable design and comprehensive management features enable efficient monitoring and maintenance.

In conclusion, the Cabletron Systems 3T02-04 stands out as a powerful and versatile networking solution that combines cutting-edge technologies, multi-port capabilities, VLAN support, and excellent scalability, making it a valuable asset for any organization aiming to optimize its network infrastructure.
Top Page Image Contents