Cabletron Systems 3T02-04 manual Adding/Swapping Modules

Page 40

Chapter 6: Adding/Swapping Modules

If the module you are adding has a different number of ports than the module you are removing, before you can power cycle the ATX you must:

•Delete all static addresses

•Delete all ARP addresses and IP routing table entries

•Delete all filters

1.Make sure the ATX is powered off.

2.Remove the network connections from the module you are going to replace.

3.Loosen the screws at each end of the front panel of the interface module you are going to replace.

4.Remove the installed interface module by pulling gently but firmly on the ears at the ends of the module's front panel.

5.Gently slide the new module into the plastic guides in the module slot until it is completely inserted. Push the module firmly into place, as far as it will go, to fully engage the connectors at the back of the module with the backplane at the rear of the ATX chassis.

6.Tighten the screws on each side of the Token Ring module front panel.

7.Power on the ATX, and check the module LED power-on sequence as described in Chapter 2, Connecting to the Network.

8.Make the connections to the network as described in Chapter 2.

Page 6-2

Token Ring Switch Module User Guide

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Token Ring Switch Module Page Token Ring Switch Module User Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents Chapter Introduction Document Conventions Related Manuals Getting HelpGeneral Description Connectors StandardsLEDs POWER-UP LED Sequence Chapter Connecting to the NetworkIntroduction Connecting the Token Ring Module to a HUB Typical ConfigurationsUnshielded Twisted Pair Connecting a Token Ring Module to a UTP Hub Shielded Twisted PairConnecting a Token Ring Module to an STP MAU Chapter Configuring Connecting the LCM LCM CommandsConfiguring the Bridging Type Setting the Ring SpeedTransparent Bridging Method Source Routing and SRTSegment Number Bridge Number Translation OptionsARP Translation Source Routing ARP Translation IPX TranslationAppleTalk Translation ATX translate 4-6 apple on Configuring Token Ring Switch Module User Guide Chapter Statistics Displaying Port StatusStatistics Displaying Port Status Module Statistics Destination Addresses and Forwarding OutcomesModule Statistics Statistics Token Ring Switch Module User Guide POWER-UP Diagnostics Chapter Diagnostics and TroubleshootingPower-up Tests Operational Diagnostics Power-up ResultsLoopback Tests Troubleshooting Diagnostic ResultsIf the Module Fails to Power Up Connectivity Problems Adding a Token Ring Switch Module Unpacking the Token Ring Switch ModuleChapter ADDING/SWAPPING Modules Adding/Swapping Modules Swapping a Module Token Ring Switch Module User Guide Appendix a Technical Specifications TCP/IP IPXDB9 for STP RJ45 for UTP Appendix B Bridging Methods OverviewTransparent Bridging Appendix B Bridging MethodsSource Routing Bridging Figure B-1 Source Routing ExampleB-4 Token Ring Switch Module User Guide Source Routing Transparent Bridging B-6 Token Ring Switch Module User Guide Index ATXIndex Index-2 Token Ring Switch Module User Guide

3T02-04 specifications

Cabletron Systems, a notable name in the networking industry, gained prominence for its pioneering products and innovative technologies. One of its formidable offerings is the Cabletron Systems 3T02-04, an advanced network switching device designed to cater to the evolving demands of high-performance networking environments.

The Cabletron Systems 3T02-04 excels in facilitating seamless data transfer within various network infrastructures. At its core, this device is engineered with key features that enhance its performance and adaptability. With a robust switching architecture, it provides high throughput and low latency, ensuring efficient handling of data traffic. This is particularly crucial for organizations that rely on rapid communication and data exchange for their operations.

One of the defining characteristics of the 3T02-04 is its multi-port configuration, which allows multiple devices to connect simultaneously. This enables the device to support a wide range of applications, from standard office networking to intensive data center operations. Equip with support for various data transmission protocols, including Ethernet, the 3T02-04 is highly versatile, meeting the diverse needs of modern networking tasks.

Additionally, Cabletron Systems incorporated advanced technologies such as Virtual LAN (VLAN) support in the 3T02-04, enhancing network segmentation and improving security measures. This feature allows network administrators to partition the network into different segments, ensuring that sensitive data remains separate and secure from other less critical services.

The 3T02-04 is also notable for its scalability. As organizations grow and their networking requirements evolve, the 3T02-04 can adapt. This scalability is crucial for businesses looking to future-proof their infrastructure investments, allowing them to add bandwidth and enhance connectivity without a complete overhaul of their existing systems.

Moreover, the robustness and reliability of the device ensure that it can withstand the rigors of demanding environments. Its durable design and comprehensive management features enable efficient monitoring and maintenance.

In conclusion, the Cabletron Systems 3T02-04 stands out as a powerful and versatile networking solution that combines cutting-edge technologies, multi-port capabilities, VLAN support, and excellent scalability, making it a valuable asset for any organization aiming to optimize its network infrastructure.
Top Page Image Contents