Cabletron Systems 150 manual Configure the Cyberswitch

Page 98

EXAMPLE NETWORKS

CONFIGURE THE CYBERSWITCH

Note: The software should have already been installed and you need the system prompt before proceeding with these steps.

Using the detailed instructions for these steps found in the Simple Remote Bridging chapter, complete the following configuration steps for SITE1.

Start the CFGEDIT program

Select physical resources

Select to add a resource

Select Switch type to be NI-1

Select to add a line

Enter the line name

Select slot and port numbers

Select line interface type of “Point-to-Point”

Add Data Links (Data Link explanation follows)

Choose Auto TEI Negotiation

Enter Service Profile ID (SPID) Value

Enter Directory Number for Data Link

Enter Maximum Number of Digits to Verify

Repeat “Add Data Links” for second Data Link

Repeat “Select to add a line” for each additional line

Data links are handled differently on a NI-1 switch. Some BRI lines have only one phone number (for the Data Link), but can handle two calls (one for each bearer channel). For NI-1 switches, the BRI line has two phone numbers (one for each bearer channel), and each phone number has its own SPID. You must enter the number of digits to verify, so that when the system receives a phone call it can determine on which bearer to accept the phone call. Refer to the System Details worksheet for the SPIDs, directory numbers, and the number of digits to verify.

The sections below provide instructions for completing the remaining configuration steps for SITE1.

CONFIGURING THE OPTIONS

By default, AppleTalk Routing is disabled. Before we can begin configuring the AppleTalk feature, we must first enable AppleTalk Routing. From the Options Menu, select AppleTalk Routing (Enable/ Disable). Follow the onscreen instructions to enable AppleTalk Routing. The following expanded screen will then be displayed:

AppleTalk Routing Menu:

1)AppleTalk Routing (Enable/Disable)

2)AppleTalk Ports

3)AppleTalk Static Routes

4)Isolated Mode (Enable/Disable)

Select function from above or <RET> for previous menu:

We will use this menu to configure SITE1’s AppleTalk information.

98 CyberSWITCH

Image 98
Contents Example Networks Virus Disclaimer Trademarks DOC Notice Contents IP Routing Network with Remote Bridge Devices Index Example Networks Simple Remote Bridging Network Resources LinesBridging and Routing Information IP RoutingConfigure the Cyberswitch Line Type = Brisdn Pointtopoint Pointmultipoint Isdn Save Configuration Files Verify the Installation Remote Bridging Network with Security Isdn BRI Device Information Calling ISDN, FR, etc. InformationPat Smith IP Routing Enabled Disabled Mode of Operation Router Configure the Cyberswitch Configuring the OptionsConfiguring the Security Isdn PPP Verify the Installation IP Routing Network Site System Details Rick Jill Ralph Todd SanFran Configuring the Cyberswitch Options SnmpConfiguring the IP Interface Information WAN Rlan LAN WAN Device Name? Rick Bear Device Authentication Menu Device = Rick Bear Return to the Security Configuration Menu Verify the Installation IP Routing Network with Remote Bridge Devices Business AssumptionsIsdn Resources 123123123123 Carmel CorpOffice ENABLE/DISABLE Bridging Configuring the IP Interface Information WAN Rlan Return to the Main Menu Device Name? Monterey Device Table Menu Device = Monterey 198.12.10.0 Save Configuration Files IP Routing Network with PPP Devices IP Routing Network with PPP Devices BRI 5ESS For Site BridgingLAN2 For Site 918105551234 Configure SITE1 Configuring the System OptionsConfiguring the IP Interface Information Screen interaction will resemble the following Device Name? SITE2 Device Table Menu Device = SITE2 Base Data Rate 64000 bps Initial Maximum 384000 bps Configuring Static Routes LAN Interface CSX150 Finishing the Security Configuration Configure SITE2 Configuring SITE2 OptionsConfiguring Security Example Networks IPX Routing Network Masternet Ethernet-1 64000 bps 128000 bps Obpswd Bridging and Routing Information IPX Routing Configure Devices ADD IPX WAN DeviceIsdn Information Configure System Options RIP/SAPAdd a LAN Interface Add a Remote LAN Interface Finally, you’ll see this screen IPX Static Routes Save Configuration Files Appletalk Routing Network Network Topology MAC SITE1 Appletalk Routing AppleTalk Routing/Port InformationPPP Configure the Cyberswitch Configuring Appletalk Port Information Example Networks Configuring Device Information Disabled Again, return to the Device Table Menu Configuring AN Appletalk Static Route Verify the Installation Index

150 specifications

Cabletron Systems 150, a notable networking device in the pantheon of computer networking technology, was introduced during a pivotal period in the evolution of network infrastructure. Designed to support the rapidly growing demands of organizations, it quickly became known for its robust performance and versatility.

One of the standout features of the Cabletron Systems 150 is its ability to function as a multiport repeater and a path to high-speed network connections. This versatility means that the device can connect multiple segments of a network while maintaining the integrity and efficiency of data transmission. The device is designed for multiple data rates, accommodating both 10BASE-T and 100BASE-T technologies, making it suitable for various types of networks, from traditional Ethernet setups to more advanced Fast Ethernet configurations.

The Cabletron 150 was built using advanced technologies that allowed for increased bandwidth and reduced latency. Its ability to handle various protocols made it indispensable in environments that required seamless communication across diverse systems. Network managers appreciated the device's Layer 2 switching capabilities, which facilitated faster data flow and minimized broadcast traffic on the network, enhancing overall performance.

Another significant characteristic of the Cabletron Systems 150 is its modular design. This architecture enables users to upgrade or expand the system based on their changing networking needs, providing a future-proof solution that adapts to evolving technology landscapes. With a range of interface options, the device can support twisted pair and fiber optic connections, catering to organizations with different infrastructural preferences.

The Cabletron Systems 150 also stands out for its ease of management. Network administrators could remotely monitor and configure the device, allowing for efficient troubleshooting and maintenance. The inclusion of SNMP (Simple Network Management Protocol) capabilities further simplified network management tasks, helping IT teams ensure optimal performance.

In summary, the Cabletron Systems 150 was a pioneering networking device characterized by its multiport repeater functionality, compatibility with multiple protocols, high-speed data transmission capabilities, and modularity. It served as a reliable backbone for organizations aiming to enhance their network performance while providing scalability for future needs. The legacy of Cabletron Systems 150 continues to be felt in the networking world, reflecting the early innovations that laid the groundwork for today’s complex networking technologies.