Extron electronic ISM 824 manual Reference Information, cont’d

Page 162

Reference Information, cont’d

Sync — ISM VS

Input type

Pass-through RGBHV, RGBS, RGsB

Output type

RGBHV, RGBS, RGsB

 

Bi-level on Y, R-Y, B-Y channels (component video)

Standards

NTSC 3.58, NTSC 4.43, PAL, SECAM

Input level

0.5 V to 5.0 Vp-p, unterminated. 4.0 Vp-p normal.

Output level

TTL: 5.0 Vp-p, unterminated

Input impedance

75 ohms

Output impedance

75 ohms

Max. input voltage

5.0 Vp-p

Max. propagation delay

30 ns (RGB pass-through

Audio

Gain

Unbalanced output: -6 dB

 

Balanced output: 0 dB

Frequency response

20 Hz to 20 kHz, ±0.5 dB

THD + nouse

0.03% @ 1 kHz at nominal level, 0 dB gain

S/N

>90 dB, at maximum rated output drive

Crosstalk

<-80 dB @ 1 kHz, fully loaded

Stereo channel separation

>90 dB @ 1 kHz

CMRR

>75 dB @ 20 Hz to 20 kHz

Audio input

Number/signal type

8 stereo, balanced/unbalanced

Connectors

(8) 3.5 mm captive screw connector, 5 pole

Impedance

>10k ohms, balanced/unbalanced, DC coupled

Nominal level

+4 dBu (1.23 V), -10 dBV (316 mV)

Maximum level

+19.5 dBu, (balanced or unbalanced) at 1% THD+N

Input gain adjustment

-18 dB to +24 dB

N0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu

Audio output

Number/signal type

2 (base model, upgradeable to 8) stereo, balanced/unbalanced

Connectors

(2, upgradeable to 8) 3.5 mm captive screw connectors, 5 pole

Impedance

50 ohms unbalanced, 100 ohms balanced

Gain error

±0.5 dB channel to channel

Maximum level (Hi-Z)

>+21 dBu, balanced or >+15 dBu unbalanced at 1% THD+N

Maximum level (600 ohm)

>+15 dBu, balanced or unbalanced at stated 1% THD+N

Output volume range

0 to 64 (-64 dB to 0 dB) in 1 dB increments from steps 1 through 64.

Control/remote — switcher

Serial host control port

1 rear panel RS-232 or RS-422, 9-pin female D connector

 

1 front panel RS‑232 2.5 mm mini stereo jack

Baud rate and protocol

9800 baud, 8 data bits, 1 stop bit, no parity

Serial control pin configurations

 

 

9-pin D connector

RS‑232: 2

= TX, 3 = RX, 5 = GND

 

RS‑422: 2

= TX-, 3 = RX-, 5 = GND, 7 = RX+, 8 = TX+

2.5mm mini stereo jack........ RS‑232: tip = TX, ring = RX, sleeve = GND

Ethernet control port

1 RJ-45 female connector

Ethernet data rate

10/100Base-T, half/full duplex with autodetect

B-4 ISM 824 Integration Scaling Multiswitcher• Reference Information

Page 161 Page 163
Image 162
Page 161 Page 163
Contents Integration Scaling Multiswitcher ISMSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolISM 824 Integration Scaling Multiswitcher FCC Class a NoticeIi ISM 824 Integration Scaling Multiswitcher ISM 824 Integration Scaling Multiswitcher Quick Start QS-1 Pass-through outputs Connect videoQuick Start ISM 824 Integration Scaling Multiswitcher QS-2 ISM 824 Integration Scaling Multiswitcher Quick StartMaking input to output ties ISM 824 Integration Scaling Multiswitcher Quick Start QS-3 Picture adjustmentsPresets OUT #5ISM 824 Menu System Front panel security lockout Executive modeQS-4 ISM 824 Integration Scaling Multiswitcher Quick Start Menu button The MenuTable of Contents Table of Contents, cont’d Page Table of Contents, cont’d Sys  tems  s  ettings  page IP Settings  fields  Rev. a One About the Integration Scaling Multiswitcher ISM 824 Integration Scaling Multiswitcher IntroductionAbout this Manual Typical ISM 824 application Introduction, cont’d DefinitionsOutputs FeaturesInputs Tie any input to any or all outputsOptional Output Card Features Universal Scaler card ISM RGBVideo Scaler card ISM VS Dual Output Wideband card ISM 2WBSingle Output Wideband card ISM 1WB Introduction, cont’d Two Important safety instructions Installationstallation, cont’dUL/Safety Requirements ISM 824 Integration Scaling Multiswitcher InstallationUL requirements for rack mounted devices Mounting the SwitcherTabletop placement Rack mountingInstallation, cont’d Rear Panel Features and ConnectionPower and control connections Cabling and RJ-45 connector wiring Choosing a network cableTerminating the network cable Input connections Input connections for various video formatsOutput connections Balanced Stereo OutputOptional output card connections Video output connectionsAudio output connections Installing the optional output cards PlaceIf applicable, repeat for any other output cards Cover Three Front Panel Features Input and output buttonsControl buttons Control selection buttons These four buttonsEnter button The Enter button flashes green Operation and Setup, cont’d Powering Up Default display cycleLCD begins the default display cycle Video only green Front Panel OperationMaking input to output ties Green video onlyAn example of creating a set of video and audio ties Press and release the Enter button figureViewing ties Press the View button lights redAdding ties to existing ties Press and release the Esc button see -8. The View buttonRemoving ties Press View and observe the LCD display see figurePress and release the Esc button see -12. The View button Press Esc to clear View and reset the LCD Another video input can now be tied to outputs 2Replacing ties Press and release the Esc button see -16. The View buttonView V=7-22-3-- Ties A=2388-33 Input/Output grouping10001010 An example of creating a set of I/O groupsVI EW V=7-22-3 Press Esc to clear all pending changes and reset the LCD=2388-33 Muting an outputViewing and setting the RGB delay Viewing the RGB delayUnmuting an output OUT #3 RGB Delay Changing the RGB delayInput audio level gain and output audio volume Viewing input audio level and output audio volumeGain = Adjusting input audio level and output audio volume See -26. The range is -18 dB to +24 dBPresets Saving a presetOverview Save Preset #11 Recalling a presetBrightness Picture adjustmentsColor/Tint ContrastAdjusting the picture color/tint Adjusting the picture brightness/contrastAdjusting the picture detail Press the Esc button to clear all button and reset the LCDBRT OUT #5 Adjusting the picture position Adjusting the picture sizeCurrent size setting see -37 for that output Adjusting the picture zoom =1024Background illumination settings Front panel security lockout Executive modes40 Executive Mode 2 initiation and exit method ISM 824 Menu System Auto Image menuInput configuration menu Input CongurationOutput card configuration menu Universal Scaler configuration menuScalerUniversal Right encoder to adjust the V line value Input Setup submenuTo adjust the H pixel value, and rotate Select Output submenuOutput Config submenu Output Configuration Scaler boardsUser Presets submenu Press Next to return to the upper level Output Config. menuPress Menu to go to the next submenu User Presets Press Next to return to the User Preset menuSplit Grayscale Advanced Config submenuSplit Color Bars Aspect ratioDefault ISM 824 Integration49 Video Scaler output resolution/refresh rate table User Presets Within this submenu, up to 3 presets can be saved or erasedAdvanced Config Adjusted. Default setting is View Comm Settings menu InputEditing the communication settings System Reset Menu Exit menuScreen. Use this menu to exit from the device Resetting the Unit with the Reset Button Reset Mode Comparison SummaryFour Pin Front Panel Configuration PortRS-232/RS-422 Link RS-232 Function RS-422Ethernet Link SymbolsDefault address Ethernet connectionISM 824 specific symbol definitions SIS Programming and Control, cont’dX5 = Input selection Switcher-Initiated MessagesPower-up Input and output video typeReconfig Auto ImageAuto Memory Host-to-Switcher Instructions Switcher Error ResponsesUsing the Command/Response Tables Control, cont’d Command/Response Table for SIS CommandsProgramming OutX@ InX! RGBRprX4 @ $TypX!*X# SprX4@*0B @*1B@Vmt1 @Vmt0X! ...Vid X5! X5! X5Mut X5! X5! X5 Vgp X4Out*X! XInf X\X\X\X\ \X\X\X\\ X\ X\ Multiswitcher SIS Programming and Control Front panel lockout executive modeX4*,X4 @*X$ @%2AX$ @HstX!*X$ ZpgX4ZpxX5 @*X% @%2AX% @VstX!*X%13*X@*X # 12*X@*X* #@ApxX!*X @AlnX!*X@+Y @BrtX!*X1% @*X1% @%2AX1% @ConX!*X1%@*X1%Y @%2AX1% Y @BrtX!*X1% @-Y @BrtX!*X1%X1*X1*X1&*X1 @ZomX!*X5$*X1&*X1EscX@,X1*X1*X1&*X1&XY WX@,X1%2AX1%2AX1 @*X2!*X2@ = @%2AX2!%2AX2@ = RteX@*X2!*X2@@SprX@*X2 @*X2@RprX@*X2 @*X2% @%2AX2% @RprX2%@*0M Video Scaler ISM VS Output@*1M @ImgX@VphX!*X1 @HszX!*X1@VszX!*X1 @Pol X\ @*X2!*X2@ =@*X\# @*X2%@Blu1 @FlmX@ Frz1 16*X@*X1#@ImgX! *0 @*X1% @%2AX1% @BlbX!*X1%@ImgX! *1 Bottom blankingX7 = Command/Response Table for IP SIS CommandsSymbol definitions X7$ =X7# IpnX7IptX7@ IpzX7$X8#,X8$ X8@EX8!,X8#,X8$,X8$, ... X8$EM X8$Five ISM 824 Windows Control Program Installing the softwareInstallation from the CD-ROM Extron software CD window appears figureInstallation from the Web site Download Center WebISM 824 Multiswitcher Software, cont’d Using the softwareIf connecting by TCP/IP If connecting by RS-232 Extron ISM 824 Control Program main window -5 appearsFile Menu featuresControl program menus and pages ToolsData tracer window 10 ISM 824 I/O Group Settings menus − all groups cleared 11 ISM 824 I/O grouping completed 13 ISM 824 Unit Settings menus − IP and RS-232 windows Window Extron Firmware Loader appears 15 Firmware Loader window with selected firmware fileHelp ISM 824 Windows Control programSelect the Video/audio mode Follow all or Breakaway Creating a tieRemoving a tie Muting or unmuting output signals 20 Output video and audio signal muting22 Recalling a preset SettingsConfiguring the input video signal type Creating or editing input and output namesSetting the RBG delay Audio SettingsAdjusting the input gain and attenuation Adjusting the output volume levelPress Enter. The output’s volume is set to that level Output Cards Create an input to output tieMaking picture adjustments Selecting an aspect ratioSelecting a test pattern Recalling an input preset Saving or recalling user presetsSaving input presets Deselecting or re-selecting auto memoryStarting auto image Freezing an imageMaking input to output ties Setting top and bottom blanking values Recalling an input preset Using the Button Label Generator software Button Label GeneratorReplacing the button labels 34 Remove the button cap to replace the labelISM 824 Multiswitcher Software, cont’d Html Operation Downloading the Startup To access the ISM 824 using Html pages do the followingISM 824 Integration Scaling Multiswitcher Html Operation Start the Web browser programSystem Status System StatusHtml Operation, cont’d Configuration PagesSystem Settings page IP Settings fields Unit Name fieldGateway IP Address field Dhcp radio buttonsIP Address field Subnet Mask fieldSystem Settings page Date/Time Settings fields ISM SettingsClick the desired value Input configuration RGB delayPasswords Executive modeEmail Alerts Click Edit. The Edit button changes to Save Setting up e-mail alertsSetting up Smtp authorization Eml extension that contains the messageFirmware Upgrade Both a user name and a password must be specifiedClick the Firmware Upgrade link see figure Access the ISM 824 using Html pages as described onClick the Configuration tab PortFile Management Enter the new directory name in the Dir/ fieldControl Pages User Control12 Click in an output field to see the drop down list 13 A/V mute buttons status according to signal type 14 I/O Presets Universal Scaler ISM RGB Slot output card configurationEach configurable card has its own For the Universal Scaler is shown belowUser and input presets can be saved and/or recalled Video Scaler ISM VS For the Video Scaler is shown belowSpecial Characters Space spaces are accepted in names + ~ , @ = ‘ ’ semicolonAAppendix a Ethernet Connection Ping to determine Extron IP addressConnect as a Telnet client Ping to determine Web IP addressOpen Ethernet Connection, cont’dTelnet tips Escape character and Esc keyClose Local echoSet carriage return-line feed QuitLocal and remote devices Subnetting a PrimerGateways IP addresses and octetsDetermining whether devices are on the same subnet Unmasked octets are compared indicated by ? in figure A-6Masked octets are not compared indicated by X in figure A-6 Ethernet Connection, cont’d AppendixBB Specifications ReferenceInformation,co t’d50 Hz, 60 Hz, 72 Hz, 96 Hz, 100 Hz, or 120 Hz Vp-p for Y of component videoTo 1.0 Vp-p Scaled RGBHV, RGBS, RGsB, HD digital component video YUVReference Information, cont’d Gateway = Extron’s control/configuration program for WindowsARP, Icmp ping, TCP/IP, Telnet, Http Dhcp = offISM 824 part number Part Numbers and AccessoriesAccessories Included partsAsia Japan JapanExtron Electronics. All rights reserved
Related manuals
Manual 1 pages 21.49 Kb
Top Page Image Contents