Extron electronic ISM 824 manual Adjusted. Default setting is

Page 72

Operation and Setup, cont’d

3.	Press Next to go to the Top and Bottom Blanking menu. Within this menu
	the top and bottom blanking area (0-255) shown on the display output can be
	adjusted. Default setting is 000.
	Rotate the left front panel encoder ([) to adjust the top blanking value, and
	rotate the right encoder ({) to adjust the bottom blanking value.
4.	Press Next to go to the (encoder) Filter Mode menu. Filter Mode can be
	turned on or off from this menu. Default setting is on.
	Rotate either front panel encoder to tun the Filter mode off or on. When
	turned on, the filter reduces or eliminates anti-aliasing (the jail bar effect) and
	high frequency noise for digital displays. Set the filter to off for CRT displays.
5.	Press Next to go to the Blue Mode menu. Blue Mode can be turned on or off
	from this menu. Default setting is off.
	Rotate either front panel encoder to tun the blue mode on or off. When turned
	on, only sync and the blue video signals are displayed.
6.	Press Next to go to the Auto Memories menu. Auto Memories can be turned
	on or off from this menu. Default setting is on.
	Rotate either front panel encoder to tun the auto memory on or off
7.	Press Next to go to the 2:2 pulldown menu. The pulldown detection feature
	can be turned off or on from this menu. If the input source is PAL video that
	originated in film, set the 2:2 pulldown to on. For standard PAL video sources
	(cameras, etc.), set it to off. Default setting is on.

N2:2 pulldown is not applicable for NTSC video sources, as film mode (3:2 pulldown) is automatically detected for those signals.

9. Rotate either front panel encoder to tun the 2:2 pulldown mode off or on.

10. Press Next to go to the Enhanced Mode menu. The enhanced mode can be turned on or off from this menu. Default setting is off.

N Only S-video and composite video input signals support Enhanced mode.

11. Rotate either front panel encoder to turn the enhanced mode on or off. When the mode is set to on, automatic gain control of the video signal is enabled.

12. Press Next to return to the Advanced Config. menu.

NPress Menu to go directly to the next top level menu (View Comm Settings).

3-40 ISM 824 Integration Scaling Multiswitcher • Operation and Setup

Image 72

Contents Integration Scaling Multiswitcher ISMSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolISM 824 Integration Scaling Multiswitcher FCC Class a NoticeIi ISM 824 Integration Scaling Multiswitcher ISM 824 Integration Scaling Multiswitcher Quick Start QS-1 Pass-through outputs Connect videoQuick Start ISM 824 Integration Scaling Multiswitcher QS-2 ISM 824 Integration Scaling Multiswitcher Quick StartMaking input to output ties Picture adjustments PresetsISM 824 Integration Scaling Multiswitcher Quick Start QS-3 OUT #5Front panel security lockout Executive mode QS-4 ISM 824 Integration Scaling Multiswitcher Quick StartISM 824 Menu System Menu button The MenuTable of Contents Table of Contents, cont’d Page Table of Contents, cont’d Sys tems s ettings page IP Settings fields Rev. a One About the Integration Scaling Multiswitcher ISM 824 Integration Scaling Multiswitcher IntroductionAbout this Manual Typical ISM 824 application Introduction, cont’d DefinitionsFeatures InputsOutputs Tie any input to any or all outputsOptional Output Card Features Universal Scaler card ISM RGBVideo Scaler card ISM VS Dual Output Wideband card ISM 2WBSingle Output Wideband card ISM 1WB Introduction, cont’d Two Installationstallation, cont’d UL/Safety RequirementsImportant safety instructions ISM 824 Integration Scaling Multiswitcher InstallationMounting the Switcher Tabletop placementUL requirements for rack mounted devices Rack mountingInstallation, cont’d Rear Panel Features and ConnectionPower and control connections Cabling and RJ-45 connector wiring Choosing a network cableTerminating the network cable Input connections Input connections for various video formatsOutput connections Balanced Stereo OutputOptional output card connections Video output connectionsAudio output connections Installing the optional output cards PlaceIf applicable, repeat for any other output cards Cover Three Front Panel Features Input and output buttonsControl buttons Control selection buttons These four buttonsEnter button The Enter button flashes green Operation and Setup, cont’d Powering Up Default display cycleLCD begins the default display cycle Front Panel Operation Making input to output tiesVideo only green Green video onlyAn example of creating a set of video and audio ties Press and release the Enter button figureViewing ties Press the View button lights redAdding ties to existing ties Press and release the Esc button see -8. The View buttonRemoving ties Press View and observe the LCD display see figurePress and release the Esc button see -12. The View button Press Esc to clear View and reset the LCD Another video input can now be tied to outputs 2Replacing ties Press and release the Esc button see -16. The View buttonView V=7-22-3-- Ties A=2388-33 Input/Output grouping10001010 An example of creating a set of I/O groupsPress Esc to clear all pending changes and reset the LCD =2388-33VI EW V=7-22-3 Muting an outputViewing and setting the RGB delay Viewing the RGB delayUnmuting an output OUT #3 RGB Delay Changing the RGB delayInput audio level gain and output audio volume Viewing input audio level and output audio volumeGain = Adjusting input audio level and output audio volume See -26. The range is -18 dB to +24 dBPresets Saving a presetOverview Save Preset #11 Recalling a presetPicture adjustments Color/TintBrightness ContrastAdjusting the picture color/tint Adjusting the picture brightness/contrastAdjusting the picture detail Press the Esc button to clear all button and reset the LCDBRT OUT #5 Adjusting the picture position Adjusting the picture sizeCurrent size setting see -37 for that output Adjusting the picture zoom =1024Background illumination settings Front panel security lockout Executive modes40 Executive Mode 2 initiation and exit method ISM 824 Menu System Auto Image menuInput configuration menu Input CongurationOutput card configuration menu Universal Scaler configuration menuScalerUniversal Input Setup submenu To adjust the H pixel value, and rotateRight encoder to adjust the V line value Select Output submenuOutput Config submenu Output Configuration Scaler boardsPress Next to return to the upper level Output Config. menu Press Menu to go to the next submenu User PresetsUser Presets submenu Press Next to return to the User Preset menuAdvanced Config submenu Split Color BarsSplit Grayscale Aspect ratioDefault ISM 824 Integration49 Video Scaler output resolution/refresh rate table User Presets Within this submenu, up to 3 presets can be saved or erasedAdvanced Config Adjusted. Default setting is View Comm Settings menu InputEditing the communication settings System Reset Menu Exit menuScreen. Use this menu to exit from the device Resetting the Unit with the Reset Button Reset Mode Comparison SummaryFour Front Panel Configuration Port RS-232/RS-422 LinkPin RS-232 Function RS-422Symbols Default addressEthernet Link Ethernet connectionISM 824 specific symbol definitions SIS Programming and Control, cont’dX5 = Switcher-Initiated Messages Power-upInput selection Input and output video typeReconfig Auto ImageAuto Memory Host-to-Switcher Instructions Switcher Error ResponsesUsing the Command/Response Tables Command/Response Table for SIS Commands ProgrammingControl, cont’d OutX@ InX! RGB@ $ TypX!*X#RprX4 SprX4@*1B @Vmt1@*0B @Vmt0X5! X5! X5 Mut X5! X5! X5X! ...Vid Vgp X4Out*X! XInf X\X\X\X\ \X\X\X\\ X\ X\ Multiswitcher SIS Programming and Control Front panel lockout executive modeX4*,X4 ZpgX4 ZpxX5@*X$ @%2AX$ @HstX!*X$ @*X% @%2AX% @VstX!*X%12*X@*X* # @ApxX!*X13*X@*X # @AlnX!*X@*X1% @%2AX1% @ConX!*X1% @*X1%Y @%2AX1% Y @BrtX!*X1%@+Y @BrtX!*X1% @-Y @BrtX!*X1%@ZomX!*X5$*X1&*X1 EscX@,X1*X1*X1&*X1&XY WX@,X1%2AX1%2AX1X1*X1*X1&*X1 @*X2!*X2@ = @%2AX2!%2AX2@ = RteX@*X2!*X2@@*X2 @RprX@*X2@SprX@*X2 @*X2% @%2AX2% @RprX2%Video Scaler ISM VS Output @*1M@*0M @ImgX@VphX!*X1 @HszX!*X1@VszX!*X1 @*X2!*X2@ = @*X\#@Pol X\ @*X2%@FlmX @ Frz1@Blu1 16*X@*X1#@*X1% @%2AX1% @BlbX!*X1% @ImgX! *1@ImgX! *0 Bottom blankingCommand/Response Table for IP SIS Commands Symbol definitionsX7 = X7$ =IpnX7 IptX7@X7# IpzX7$X8@ EX8!,X8#,X8$,X8$, ... X8$EMX8#,X8$ X8$Five Installing the software Installation from the CD-ROMISM 824 Windows Control Program Extron software CD window appears figureInstallation from the Web site Download Center WebISM 824 Multiswitcher Software, cont’d Using the softwareIf connecting by TCP/IP If connecting by RS-232 Extron ISM 824 Control Program main window -5 appearsMenu features Control program menus and pagesFile ToolsData tracer window 10 ISM 824 I/O Group Settings menus − all groups cleared 11 ISM 824 I/O grouping completed 13 ISM 824 Unit Settings menus − IP and RS-232 windows Window Extron Firmware Loader appears 15 Firmware Loader window with selected firmware fileHelp ISM 824 Windows Control programSelect the Video/audio mode Follow all or Breakaway Creating a tieRemoving a tie Muting or unmuting output signals 20 Output video and audio signal muting22 Recalling a preset SettingsConfiguring the input video signal type Creating or editing input and output namesSetting the RBG delay Audio SettingsAdjusting the input gain and attenuation Adjusting the output volume levelPress Enter. The output’s volume is set to that level Output Cards Create an input to output tieMaking picture adjustments Selecting an aspect ratioSelecting a test pattern Saving or recalling user presets Saving input presetsRecalling an input preset Deselecting or re-selecting auto memoryStarting auto image Freezing an imageMaking input to output ties Setting top and bottom blanking values Recalling an input preset Using the Button Label Generator software Button Label GeneratorReplacing the button labels 34 Remove the button cap to replace the labelISM 824 Multiswitcher Software, cont’d Html Operation To access the ISM 824 using Html pages do the following ISM 824 Integration Scaling Multiswitcher Html OperationDownloading the Startup Start the Web browser programSystem Status System StatusConfiguration Pages System Settings page IP Settings fieldsHtml Operation, cont’d Unit Name fieldDhcp radio buttons IP Address fieldGateway IP Address field Subnet Mask fieldSystem Settings page Date/Time Settings fields ISM SettingsClick the desired value Input configuration RGB delayPasswords Executive modeEmail Alerts Setting up e-mail alerts Setting up Smtp authorizationClick Edit. The Edit button changes to Save Eml extension that contains the messageFirmware Upgrade Both a user name and a password must be specifiedAccess the ISM 824 using Html pages as described on Click the Configuration tabClick the Firmware Upgrade link see figure PortFile Management Enter the new directory name in the Dir/ fieldControl Pages User Control12 Click in an output field to see the drop down list 13 A/V mute buttons status according to signal type 14 I/O Presets Slot output card configuration Each configurable card has its ownUniversal Scaler ISM RGB For the Universal Scaler is shown belowUser and input presets can be saved and/or recalled Video Scaler ISM VS For the Video Scaler is shown belowSpecial Characters Space spaces are accepted in names + ~ , @ = ‘ ’ semicolonAAppendix a Ethernet Connection Ping to determine Extron IP addressConnect as a Telnet client Ping to determine Web IP addressEthernet Connection, cont’d Telnet tipsOpen Escape character and Esc keyLocal echo Set carriage return-line feedClose QuitSubnetting a Primer GatewaysLocal and remote devices IP addresses and octetsDetermining whether devices are on the same subnet Unmasked octets are compared indicated by ? in figure A-6Masked octets are not compared indicated by X in figure A-6 Ethernet Connection, cont’d AppendixBB Specifications ReferenceInformation,co t’dVp-p for Y of component video To 1.0 Vp-p50 Hz, 60 Hz, 72 Hz, 96 Hz, 100 Hz, or 120 Hz Scaled RGBHV, RGBS, RGsB, HD digital component video YUVReference Information, cont’d Extron’s control/configuration program for Windows ARP, Icmp ping, TCP/IP, Telnet, HttpGateway = Dhcp = offPart Numbers and Accessories AccessoriesISM 824 part number Included partsAsia Japan JapanExtron Electronics. All rights reserved

Related manuals

Manual 1 pages 21.49 Kb