Extron electronic manual Typical ISM 824 application

Page 17

The multiswitcher accepts up to eight video inputs of various resolutions on five

female BNC connectors per input. Depending on the output card configurations, the multiswitcher scales, down-converts, or simply passes the video inputs to output RGB or YUV video. The outputs are made on five female BNC connectors, or two 15-pin HD connectors (dual wideband card only). Inputs and outputs are made in the following signal formats:

•RGB (RGBHV, RGBS) video

•YUV-HD (HDTV) video

•Progressive YUV component video

•Interlaced YUV component video

•S-video (Y/C)

•Composite (NTSC, PAL, SECAM) video

Each video input is individually configurable for color, tint, brightness, contrast, detail, position, size, and zoom via the front panel, RS-232/RS-422, or Ethernet control. The ISM also allows the various high-resolution and low resolution video formats to be displayed on a device with a fixed resolution and aspect ratio, such as a liquid crystal display (LCD) projector, a digital light processor (DLP) projector, a plasma display, or, optionally, a DVI or HD-SDI device.

Figure 1-1 shows an example of an ISM 824 application.

Output #3: Video Scaler Board

Output #5: Universal Scaler Board

Output #7: Scan Converter Board

Output #8: Pass-thru Board

Broadcast VTR

Control System

Extron

ISM 824

Integration Scaling

Multiswitcher

8

7

5

3

-THRU 2

PASS1

8

7

6

		INPUTS 5
		4
		3
		2
	1	2
		1
	LINK	8
RESET	LINK	7
LAN	ACT	5
	RS232/RS422	6
REMOTE	RS232/RS422	4
		3
		2
		1

Sound System

Projector

Plasma Display

Codec

Document Camera

Camera

DVD

PC Laptop

Figure 1-1 — Typical ISM 824 application

ISM 824 Integration Scaling Multiswitcher • Introduction

1-3

Image 17

Contents ISM Integration Scaling MultiswitcherConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolFCC Class a Notice ISM 824 Integration Scaling MultiswitcherIi ISM 824 Integration Scaling Multiswitcher Pass-through outputs Connect video ISM 824 Integration Scaling Multiswitcher Quick Start QS-1Making input to output ties Quick Start ISM 824 Integration Scaling MultiswitcherQS-2 ISM 824 Integration Scaling Multiswitcher Quick Start Presets Picture adjustmentsISM 824 Integration Scaling Multiswitcher Quick Start QS-3 OUT #5QS-4 ISM 824 Integration Scaling Multiswitcher Quick Start Front panel security lockout Executive modeISM 824 Menu System Menu button The MenuTable of Contents Table of Contents, cont’d Page Table of Contents, cont’d Sys tems s ettings page IP Settings fields Rev. a One About this Manual About the Integration Scaling MultiswitcherISM 824 Integration Scaling Multiswitcher Introduction Typical ISM 824 application Definitions Introduction, cont’dInputs FeaturesOutputs Tie any input to any or all outputsUniversal Scaler card ISM RGB Optional Output Card FeaturesSingle Output Wideband card ISM 1WB Video Scaler card ISM VSDual Output Wideband card ISM 2WB Introduction, cont’d Two UL/Safety Requirements Installationstallation, cont’dImportant safety instructions ISM 824 Integration Scaling Multiswitcher InstallationTabletop placement Mounting the SwitcherUL requirements for rack mounted devices Rack mountingPower and control connections Installation, cont’dRear Panel Features and Connection Terminating the network cable Cabling and RJ-45 connector wiringChoosing a network cable Input connections for various video formats Input connectionsBalanced Stereo Output Output connectionsAudio output connections Optional output card connectionsVideo output connections If applicable, repeat for any other output cards Installing the optional output cardsPlace Cover Three Input and output buttons Front Panel FeaturesEnter button The Enter button flashes green Control buttonsControl selection buttons These four buttons Operation and Setup, cont’d LCD begins the default display cycle Powering UpDefault display cycle Making input to output ties Front Panel OperationVideo only green Green video onlyPress and release the Enter button figure An example of creating a set of video and audio tiesPress the View button lights red Viewing tiesPress and release the Esc button see -8. The View button Adding ties to existing tiesPress and release the Esc button see -12. The View button Removing tiesPress View and observe the LCD display see figure Another video input can now be tied to outputs 2 Press Esc to clear View and reset the LCDPress and release the Esc button see -16. The View button Replacing tiesInput/Output grouping View V=7-22-3-- Ties A=2388-33An example of creating a set of I/O groups 10001010=2388-33 Press Esc to clear all pending changes and reset the LCDVI EW V=7-22-3 Muting an outputUnmuting an output Viewing and setting the RGB delayViewing the RGB delay Changing the RGB delay OUT #3 RGB DelayGain = Input audio level gain and output audio volumeViewing input audio level and output audio volume See -26. The range is -18 dB to +24 dB Adjusting input audio level and output audio volumeOverview PresetsSaving a preset Recalling a preset Save Preset #11Color/Tint Picture adjustmentsBrightness ContrastAdjusting the picture brightness/contrast Adjusting the picture color/tintBRT OUT #5 Adjusting the picture detailPress the Esc button to clear all button and reset the LCD Current size setting see -37 for that output Adjusting the picture positionAdjusting the picture size =1024 Adjusting the picture zoomFront panel security lockout Executive modes Background illumination settings40 Executive Mode 2 initiation and exit method Auto Image menu ISM 824 Menu SystemInput Conguration Input configuration menuUniversal Scaler configuration menu Output card configuration menuScalerUniversal To adjust the H pixel value, and rotate Input Setup submenuRight encoder to adjust the V line value Select Output submenuOutput Configuration Scaler boards Output Config submenuPress Menu to go to the next submenu User Presets Press Next to return to the upper level Output Config. menuUser Presets submenu Press Next to return to the User Preset menuSplit Color Bars Advanced Config submenuSplit Grayscale Aspect ratioISM 824 Integration Default49 Video Scaler output resolution/refresh rate table Advanced Config User PresetsWithin this submenu, up to 3 presets can be saved or erased Adjusted. Default setting is Input View Comm Settings menuEditing the communication settings Screen. Use this menu to exit from the device System Reset MenuExit menu Reset Mode Comparison Summary Resetting the Unit with the Reset ButtonFour RS-232/RS-422 Link Front Panel Configuration PortPin RS-232 Function RS-422Default address SymbolsEthernet Link Ethernet connectionX5 = ISM 824 specific symbol definitionsSIS Programming and Control, cont’d Power-up Switcher-Initiated MessagesInput selection Input and output video typeAuto Memory ReconfigAuto Image Using the Command/Response Tables Host-to-Switcher InstructionsSwitcher Error Responses Programming Command/Response Table for SIS CommandsControl, cont’d OutX@ InX! RGBTypX!*X# @ $RprX4 SprX4@Vmt1 @*1B@*0B @Vmt0Mut X5! X5! X5 X5! X5! X5X! ...Vid Vgp X4Out*X! X\ X\ X\ Inf X\X\X\X\\X\X\X\ X4*,X4 Multiswitcher SISProgramming and Control Front panel lockout executive mode ZpxX5 ZpgX4@*X$ @%2AX$ @HstX!*X$ @*X% @%2AX% @VstX!*X%@ApxX!*X 12*X@*X* #13*X@*X # @AlnX!*X@*X1%Y @%2AX1% Y @BrtX!*X1% @*X1% @%2AX1% @ConX!*X1%@+Y @BrtX!*X1% @-Y @BrtX!*X1%EscX@,X1*X1*X1&*X1&XY WX@,X1%2AX1%2AX1 @ZomX!*X5$*X1&*X1X1*X1*X1&*X1 @*X2!*X2@ = @%2AX2!%2AX2@ = RteX@*X2!*X2@@RprX@*X2 @*X2@SprX@*X2 @*X2% @%2AX2% @RprX2%@*1M Video Scaler ISM VS Output@*0M @ImgX@VszX!*X1 @VphX!*X1@HszX!*X1 @*X\# @*X2!*X2@ =@Pol X\ @*X2%@ Frz1 @FlmX@Blu1 16*X@*X1#@ImgX! *1 @*X1% @%2AX1% @BlbX!*X1%@ImgX! *0 Bottom blankingSymbol definitions Command/Response Table for IP SIS CommandsX7 = X7$ =IptX7@ IpnX7X7# IpzX7$EX8!,X8#,X8$,X8$, ... X8$EM X8@X8#,X8$ X8$Five Installation from the CD-ROM Installing the softwareISM 824 Windows Control Program Extron software CD window appears figureDownload Center Web Installation from the Web siteIf connecting by TCP/IP ISM 824 Multiswitcher Software, cont’dUsing the software Extron ISM 824 Control Program main window -5 appears If connecting by RS-232Control program menus and pages Menu featuresFile ToolsData tracer window 10 ISM 824 I/O Group Settings menus − all groups cleared 11 ISM 824 I/O grouping completed 13 ISM 824 Unit Settings menus − IP and RS-232 windows 15 Firmware Loader window with selected firmware file Window Extron Firmware Loader appearsISM 824 Windows Control program HelpRemoving a tie Select the Video/audio mode Follow all or BreakawayCreating a tie 20 Output video and audio signal muting Muting or unmuting output signalsSettings 22 Recalling a presetCreating or editing input and output names Configuring the input video signal typeAudio Settings Setting the RBG delayPress Enter. The output’s volume is set to that level Adjusting the input gain and attenuationAdjusting the output volume level Create an input to output tie Output CardsSelecting a test pattern Making picture adjustmentsSelecting an aspect ratio Saving input presets Saving or recalling user presetsRecalling an input preset Deselecting or re-selecting auto memoryFreezing an image Starting auto imageMaking input to output ties Setting top and bottom blanking values Recalling an input preset Button Label Generator Using the Button Label Generator software34 Remove the button cap to replace the label Replacing the button labelsISM 824 Multiswitcher Software, cont’d Html Operation ISM 824 Integration Scaling Multiswitcher Html Operation To access the ISM 824 using Html pages do the followingDownloading the Startup Start the Web browser programSystem Status System StatusSystem Settings page IP Settings fields Configuration PagesHtml Operation, cont’d Unit Name fieldIP Address field Dhcp radio buttonsGateway IP Address field Subnet Mask fieldClick the desired value System Settings page Date/Time Settings fieldsISM Settings RGB delay Input configurationEmail Alerts PasswordsExecutive mode Setting up Smtp authorization Setting up e-mail alertsClick Edit. The Edit button changes to Save Eml extension that contains the messageBoth a user name and a password must be specified Firmware UpgradeClick the Configuration tab Access the ISM 824 using Html pages as described onClick the Firmware Upgrade link see figure PortEnter the new directory name in the Dir/ field File ManagementUser Control Control Pages12 Click in an output field to see the drop down list 13 A/V mute buttons status according to signal type 14 I/O Presets Each configurable card has its own Slot output card configurationUniversal Scaler ISM RGB For the Universal Scaler is shown belowUser and input presets can be saved and/or recalled For the Video Scaler is shown below Video Scaler ISM VSSpace spaces are accepted in names + ~ , @ = ‘ ’ semicolon Special CharactersAAppendix a Ping to determine Extron IP address Ethernet ConnectionPing to determine Web IP address Connect as a Telnet clientTelnet tips Ethernet Connection, cont’dOpen Escape character and Esc keySet carriage return-line feed Local echoClose QuitGateways Subnetting a PrimerLocal and remote devices IP addresses and octetsMasked octets are not compared indicated by X in figure A-6 Determining whether devices are on the same subnetUnmasked octets are compared indicated by ? in figure A-6 Ethernet Connection, cont’d AppendixBB ReferenceInformation,co t’d SpecificationsTo 1.0 Vp-p Vp-p for Y of component video50 Hz, 60 Hz, 72 Hz, 96 Hz, 100 Hz, or 120 Hz Scaled RGBHV, RGBS, RGsB, HD digital component video YUVReference Information, cont’d ARP, Icmp ping, TCP/IP, Telnet, Http Extron’s control/configuration program for WindowsGateway = Dhcp = offAccessories Part Numbers and AccessoriesISM 824 part number Included partsJapan Asia JapanExtron Electronics. All rights reserved

Related manuals

Manual 1 pages 21.49 Kb