Extron electronic IPL T PC1i setup guide Wiring for IR control, Wiring the contact Input port

Page 12

Hardware Setup, cont’d

Wiring for IR control

If you intend to control the display device via infrared (IR) commands from the PC1, you can connect an Extron IR Emitter to the IR Signal and Ground pins (pins 3 and 4) of the shared captive screw connector. The PC1 provides enough current to power one IR Emitter up to 4000 feet, or up to four Emitters for 100 feet each. See the wiring illustration below.

 

White striped wire only

IR

 

Emitter

 

 

E

Modulated IR

 

D

Ground

 

 

4000 feet (1574.8 m) maximum

 

IPL T PC1

In

S G

IPL T PC1 Shared IR and Input Connector

The PC1 can power a single IR Emitter up to 4000 feet, or four emitters wired in parallel up to 100 feet each.

Place the head of the IR Emitter over or directly adjacent to the controlled device’s IR receiver.

Chapter3Three

Wiring the contact Input port

The IPL T PC1 contact closure Input port can be connected to any device providing a closure to ground. The contact closure input is connected to 5 VDC via a 1k ohm pull-up resistor, and must be wired with a ground. This allows the input to be tied to a device such as a momentary switch, motion detector, alarm, photo eye, etc. You can define what this input will trigger via GC2.3.

1.

Connect one end of the input cable to a 3.5 mm, 5-pole

 

captive screw connector, wired appropriately, and plug it

 

into pins 1 and 2 of the shared input/IR port connector on

 

the rear panel.

2.

Connect the other end of the input cable to the input

 

device that will provide a triggering signal. (See the

 

diagram below.)

 

 

INPUT

 

 

IR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Momentary

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch

 

 

IN

 

S G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Software Setup

Creating a Global Configurator Project File

Building and Uploading a GC File

Launching the GlobalViewer Interface

2-8 IPL T PC1 Interface • Hardware Setup

Image 12
Contents Setup Guide Checklist IPL T PC1 and IPL T PC1iPrecautions Extron’s Warranty安全须知 中文 Table of Contents Table of Contents, cont’d IPL T PC1About Global Configurator IntroductionAbout this Manual About the IPL T PC1Installing Global Configurator Click the Global Configurator iconIntroduction, cont’d System requirementsTwo IPL T PC1Hardware Setup Front PanelRear Panel Hardware Setup, cont’d Connecting the HardwareWiring the Local Area Network LAN port RS-232 port cabling Download tabWiring for IR control Wiring the contact Input portSoftware Setup Creating a Global Configurator Project FileStep One Download device drivers Software Setup, cont’d Step Two Create a new projectSelect Create a New Project Select the Auto Configure IP Address check box Step Three Add a deviceStep Five Save the new Global Configurator file Step Four Define the location of the new deviceStep Six Enter contacts Step Seven Create e-mail messagesStep Nine Assign device drivers Click Add DriverCreate a group folder for your output device functions Step Ten Set scheduled actions and e-mail deliveries Click the Apply Email/Contacts button Step Eleven Set monitored conditions Step Twelve Build the Global Configurator file Or click the Build All Configurations icon shown at rightBuilding and Uploading a GC File Step Thirteen Upload the Global Configurator file Step Fourteen Change device settings if desiredSoftware Setup, cont’d Launching the GlobalViewer Interface Step Fifteen Launch GlobalViewerHttp//12.113.184.57/nortxeindex.html This page was intentionally left blank Software Setup, cont’d
Related manuals
Manual 2 pages 39.09 Kb Manual 78 pages 34.87 Kb

IPL T PC1, IPL T PC1i specifications

The Extron Electronics IPL T PC1 i and IPL T PC1 are advanced presentation and control processors designed for optimal efficiency in various audiovisual applications. These devices serve as integral components in many professional environments, offering sophisticated capabilities for managing and automating AV systems.

Both models feature a robust, intuitive user interface that simplifies the management of complex audiovisual setups. The IPL T PC1 i and IPL T PC1 enable seamless integration with a variety of control systems, enhancing the user experience and providing streamlined operation. With their scalable design, these devices can cater to the needs of small conference rooms to large auditoriums, making them versatile solutions for diverse applications.

One standout feature of the IPL T PC1 i is its support for Extron's GUI Designer software. This powerful tool allows users to create customized graphical user interfaces tailored to specific AV systems, ensuring that control remains user-friendly and accessible. The IPL T PC1 i also supports a wide range of communication protocols, including Ethernet, RS-232, and USB, which facilitates compatibility with multiple devices and technologies.

Both models are equipped with advanced signal processing capabilities. They offer support for high-resolution video formats, ensuring that presentations and multimedia displays maintain their quality. Options for signal routing and switching further enhance the functionality of the devices, allowing for dynamic and adaptive presentations.

The IPL T PC1 i and IPL T PC1 also feature built-in scheduling and automation capabilities. Users can program specific tasks, such as turning systems on or off, adjusting volume levels, and changing input sources, at predetermined times. This feature maximizes efficiency, minimizes the need for manual intervention, and ensures that AV systems are ready when needed.

In terms of physical design, both models are compact and rack-mountable, allowing for easy installation in equipment racks or dedicated AV cabinets. They also include comprehensive diagnostic tools for troubleshooting and system monitoring, ensuring optimal performance and reliability.

Overall, the Extron Electronics IPL T PC1 i and IPL T PC1 stand out as reliable, feature-rich solutions for managing AV systems in a variety of settings, making them a popular choice among AV professionals and institutions alike. Their blend of adaptability, user interface design, and robust signal processing capabilities positions them as leaders in the AV control market.