Cables to Go TE100-S55 manual Control Settings System display User selection

Page 24

Upon a successful execution of terminal emulation, your computer will establish communication with the TE100-S55 and allow you to view or modify the following settings.

Control Settings

System display

User selection

 

 

 

Switch

Switch Version No.

V1.10 (Fixed)

Configuration

Switch IP Address

168.8.xx.xx

 

 

Switch Subnet Mask

255.255.0.0

 

Default Gateway

0.0.0.0

 

Switch MAC Addr.

Factory preset (Fixed)

 

Save change

F2 key

 

Exit

F4 key

Port Configuration

Port/x State

Enable (or Disable)

 

Port/x Physical

Auto (or 100/Half, 100/Full,

 

 

10/Half, 10/Full)

 

Port/x State

Block, Learning, Listening,

 

 

Forwarding, Disable (Fixed)

 

Port/x Priority

0 (Hi) - 255 (Low)

Spanning Tree

Enable / Disable

Enable (or Disable)

Configuration

Bridge (switch) Priority

32768

 

 

Root Cost

(Reflected STA result)

 

Hello Time

10 sec. (range: 1 - 10 sec.)

 

Forward Delay Time

30 sec. (range: 4 - 30 sec.)

 

Max Age Time

40 sec. (range: 6 - 40 sec.)

 

Root Bridge

(MAC addr. of Root Bridge)

 

Root Port

(Reflected STA result)

Down-load new

Y / N

Space Key (toggle)

system firmware

Exit

F4 key

 

 

Load factory default

Y / N

Space Key (toggle)

parameters

Exit

F4 key

Filtering Data Base

Port Number

1 ~ 5

 

Port State

Disable (or Forwarding,

 

 

Blocking)

 

MAC address

Up to 16 MAC addresses

 

 

 

Table Chapter 3 -2, TE100-S55 Settings for Out-of-Band management

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents ProXpressTM FCC warning Service and support About this manual Table of Contents Index Introduction Fast Ethernet TechnologySwitching Technology Cable Specification10/100 Switching Technology Benefits of SwitchingIntroducing the TE100-S55 Although two ports are Features of TE100-S55 Getting Started Cabling Rules and Site PreparationFigure -1, Example of TE100-S55 wiring environment Figure -2, 100Base-T cabling rules Unpacking and Setup UnpackingFront Panel Figure -4, Front panel of the TE100-S55Mounting Attaching CablesPower on Adding Optional ModulesSoftware Setup Checking Status LedsConfiguring Switch IntroductionOut-of-Band Management Attaching to the RS-232 PortVT100 Terminal Control Settings System display User selection USER-SELECTIVE Parameters Page Spanning Tree Algorithm Table -3, User-selective STA parameters AT the Bridge Level AT the Port Level Timers Illustration of STA LAN Page Snmp Management Installing XPressView To Install XpressviewWhat YOU Need RAMStarting XPressView Start from ScratchOperating XPressView Open AN Existing EnvironmentSelect a Device VIEW/MODIFY Switch Configuration Modify the Spanning Tree AlgorithmMonitor Network Traffic Diagnostics Power-On Self TestSystem Status LEDs StatusSystem Diagnostic LEDs System Utilization LEDsPort Status LEDs LinkAppendices Appendix B RS-232 Pin Specification Appendix C RJ-45 Pin Specification Standard Category 3 cable, RJ-45 pin assignment Appendix D 10Base-T Module Appendix E 100Base-FX/TX Module Page Appendix F Isdn Module Page Switch Specification Port Specification10/100Mbps LAN ports fixed Index See Post

TE100-S55 specifications

The Cables to Go TE100-S55 is a reliable and efficient Ethernet switch that caters to both small office and home office environments. Designed for seamless integration into various networking applications, this compact switch offers a plethora of features and technologies that enhance performance and connectivity.

One of the main characteristics of the TE100-S55 is its five-port design, which includes five 10/100 Mbps Ethernet ports. This configuration is particularly advantageous for users looking to expand their network without the need for extensive cabling or complicated setups. Each port is auto-sensing, allowing for automatic negotiation of speed and duplex, ensuring optimal performance across connected devices.

The TE100-S55 supports a low-latency, plug-and-play setup, making it user-friendly and compatible with a wide range of operating systems and platforms. There is no need for complicated installation processes or software drivers; users can simply connect their devices, and the switch is ready to go. This feature significantly reduces downtime and improves productivity in environments where seamless connectivity is crucial.

Another notable feature of the TE100-S55 is its support for both Ethernet and Fast Ethernet connections, allowing it to adapt to various networking scenarios. It supports a data throughput of up to 200 Mbps in full-duplex mode, which is essential for bandwidth-intensive applications such as video streaming, online gaming, and large file transfers.

The switch also includes a range of technologies to enhance network performance and reliability. Features such as store-and-forward switching help to minimize packet collisions, while a built-in LED indicator provides real-time status updates on device connectivity and network activity. This awareness allows users to troubleshoot connectivity issues effectively.

In terms of energy efficiency, the TE100-S55 using a fanless design ensures quiet operation while minimizing power consumption. Its compact form factor makes it easy to place in any setting without taking up too much space.

Overall, the Cables to Go TE100-S55 Ethernet switch stands out for its combination of user-friendly features, efficient performance, and reliable connectivity. It is an ideal solution for users looking to optimize their networking experience with minimal hassle, making it a valuable addition to any small or home office environment.
Top Page Image Contents