Cables to Go TE100-S55 manual Port Status LEDs, Link

Page 44

Port Status LEDs

TE100-S55 is equipped with six Status LEDs which reflect the status of each port.

As you connect a network cable to the TE100-S55, it will auto- detect the type of cable and the corresponding 10/100 LED will light up. Likewise, depending on the port connection, the DUPLEX LED will light up to indicate its status of full or half duplex signaling.

When a port connection is active, the LINK LED will light up to indicate its operative state. Also, as activities occur on the network, the RX or TX LED will light up to indicate its transmission or reception of data.

When multiple packets are delivered at the same time, a collision will occur and the COL LED will light up. Although collisions are normal, if there’s too much, you should consider rearranging the workgroups or optimize the network for reduced traffic.

Port LED

Status

Port State

Action

 

 

 

 

10/100

On

100Mbps

 

Off

10 Mbps

 

 

 

Duplex

On

Full Duplex

 

Off

Half Duplex

 

 

 

Link

On

Port Connection Normal

 

Off

Port Connection Inactive

Check connections on

 

 

 

 

this cable segment

Tx or RX

Off

No packet traffic

 

 

Blinking

TD or RD Active

 

 

On

Heavy packet traffic

Check if consistently

 

 

 

heavy

Col

Off

No collision

Normal

 

Blinking

Collision Active

Normal

 

On

Jabber, serious problem

Check this segment

 

 

 

 

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents ProXpressTM FCC warning Service and support About this manual Table of Contents Index Introduction Fast Ethernet TechnologySwitching Technology Cable Specification10/100 Switching Technology Benefits of SwitchingIntroducing the TE100-S55 Although two ports are Features of TE100-S55 Getting Started Cabling Rules and Site PreparationFigure -1, Example of TE100-S55 wiring environment Figure -2, 100Base-T cabling rules Unpacking and Setup UnpackingFront Panel Figure -4, Front panel of the TE100-S55Mounting Attaching CablesPower on Adding Optional ModulesSoftware Setup Checking Status LedsConfiguring Switch IntroductionOut-of-Band Management Attaching to the RS-232 PortVT100 Terminal Control Settings System display User selection USER-SELECTIVE Parameters Page Spanning Tree Algorithm Table -3, User-selective STA parameters AT the Bridge Level AT the Port Level Timers Illustration of STA LAN Page Snmp Management Installing XPressView To Install XpressviewWhat YOU Need RAMStarting XPressView Start from ScratchSelect a Device Operating XPressViewOpen AN Existing Environment VIEW/MODIFY Switch Configuration Modify the Spanning Tree AlgorithmMonitor Network Traffic Diagnostics Power-On Self TestSystem Status LEDs StatusSystem Diagnostic LEDs System Utilization LEDsPort Status LEDs LinkAppendices Appendix B RS-232 Pin Specification Appendix C RJ-45 Pin Specification Standard Category 3 cable, RJ-45 pin assignment Appendix D 10Base-T Module Appendix E 100Base-FX/TX Module Page Appendix F Isdn Module Page Switch Specification Port Specification10/100Mbps LAN ports fixed Index See Post

TE100-S55 specifications

The Cables to Go TE100-S55 is a reliable and efficient Ethernet switch that caters to both small office and home office environments. Designed for seamless integration into various networking applications, this compact switch offers a plethora of features and technologies that enhance performance and connectivity.

One of the main characteristics of the TE100-S55 is its five-port design, which includes five 10/100 Mbps Ethernet ports. This configuration is particularly advantageous for users looking to expand their network without the need for extensive cabling or complicated setups. Each port is auto-sensing, allowing for automatic negotiation of speed and duplex, ensuring optimal performance across connected devices.

The TE100-S55 supports a low-latency, plug-and-play setup, making it user-friendly and compatible with a wide range of operating systems and platforms. There is no need for complicated installation processes or software drivers; users can simply connect their devices, and the switch is ready to go. This feature significantly reduces downtime and improves productivity in environments where seamless connectivity is crucial.

Another notable feature of the TE100-S55 is its support for both Ethernet and Fast Ethernet connections, allowing it to adapt to various networking scenarios. It supports a data throughput of up to 200 Mbps in full-duplex mode, which is essential for bandwidth-intensive applications such as video streaming, online gaming, and large file transfers.

The switch also includes a range of technologies to enhance network performance and reliability. Features such as store-and-forward switching help to minimize packet collisions, while a built-in LED indicator provides real-time status updates on device connectivity and network activity. This awareness allows users to troubleshoot connectivity issues effectively.

In terms of energy efficiency, the TE100-S55 using a fanless design ensures quiet operation while minimizing power consumption. Its compact form factor makes it easy to place in any setting without taking up too much space.

Overall, the Cables to Go TE100-S55 Ethernet switch stands out for its combination of user-friendly features, efficient performance, and reliable connectivity. It is an ideal solution for users looking to optimize their networking experience with minimal hassle, making it a valuable addition to any small or home office environment.
Top Page Image Contents