Gigabyte GA-K8U-939 user manual Advanced Bios Features, Hard Disk Boot Priority, Password Check

Page 34

English

2-2

Advanced BIOS Features

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

Advanced BIOS Features

 

 

`

Hard Disk Boot Priority

[Press Enter]

Item Help

 

First Boot Device

[Floppy]

 

Menu Level`

 

Second Boot Device

[Hard Disk]

 

 

 

Third Boot Device

[CDROM]

 

Select Hard Disk Boot

 

Password Check

 

[Setup]

 

Device Priority

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

Hard Disk Boot Priority

Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.

Use <> or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press <ESC> to exit this menu.

First / Second / Third Boot Device

Floppy

Select your boot device priority by Floppy.

LS120

Select your boot device priority by LS120.

Hard Disk

Select your boot device priority by Hard Disk.

CDROM

Select your boot device priority by CDROM.

ZIP

Select your boot device priority by ZIP.

USB-FDD

Select your boot device priority by USB-FDD.

USB-ZIP

Select your boot device priority by USB-ZIP.

USB-CDROM

Select your boot device priority by USB-CDROM.

USB-HDD

Select your boot device priority by USB-HDD.

LAN

Select your boot device priority by LAN.

Disabled

Disable this function.

Password Check

Setup

The system will boot but will not access to Setup page if the correct

 

password is not entered at the prompt. (Default value)

System

The system will not boot and will not access to Setup page if the correct

 

password is not entered at the prompt.

GA-K8U-939 Motherboard

- 34 -

Image 34
Contents GA-K8U-939 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8U-939 Motherboard Layout 939Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBAT Battery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 17 IRGame Game Connector Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example GA-K8U-939 / Bios Ver. F1 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupStandard Cmos Features TimeHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckOnChip Audio OnChip Sata ModeIntegrated Peripherals OnChip SataOn-Chip Primary IDE IDE DMA transfer accessOnBoard LAN Boot ROM On-Chip Secondary IDEParallel Port Mode Uart Mode SelectUR2 Duplex Mode Onboard Parallel portPME Event Wake Up Power Management SetupModem Ring Resume Resume by Alarm Power on FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/System TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen Congratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the ALi RAID Bios Entering the RAID Bios SetupCreate RAID 0 Striping for Performance Main MenuEnglish Create RAID 1 Mirroring for Reliability Create Jbod for integrated Capacity Delete All RAID Settings & Partition Delete RAID Settings & PartitionRebuild RAID Array Installing the RAID drivers Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English English English English English English Contact Us Taiwan HeadquartersChina Shanghai