Gigabyte GA-K8U-939 user manual Press Y on your keyboard to save and exit

Page 59

6.Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to

Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS defaults after BIOS has been upgraded.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Load Fail-Safe Defaults (Y/N)?Set SupervisorY	Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Press Y on your keyboard to load defaults.

7.Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu. System will reboot after you exit the BIOS menu. The procedure is completed.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software


Standard CMOS Features		Select Language
Advanced BIOS Features		Load Fail-Safe Defaults
Integrated Peripherals		Load Optimized Defaults
Power Management Setup	Save to CMOS and EXIT (Y/N)?Set SupervisorY		Password
PnP/PCI Configurations		Set User Password
PC Health Status		Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)		Exit Without Saving
ESC: Quit		F3: Change Language
F8: Dual BIOS/Q-Flash		F10: Save & Exit Setup

Time, Date, Hard Disk Type...

Press Y on your keyboard to save and exit.

Part Two:

Updating BIOS with Q-FlashTMUtility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTMutility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Top Performance
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

English

- 59 -

Appendix

Image 59

Contents GA-K8U-939 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation 939 GA-K8U-939 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector FDD FDD Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BAT BatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center Connector17 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos Game Game ConnectorEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example GA-K8U-939 / Bios Ver. F1 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordTime Standard Cmos FeaturesMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceOnChip Sata OnChip Sata ModeIntegrated Peripherals OnChip AudioOn-Chip Secondary IDE IDE DMA transfer accessOnBoard LAN Boot ROM On-Chip Primary IDEOnboard Parallel port Uart Mode SelectUR2 Duplex Mode Parallel Port ModeModem Ring Resume Power Management SetupPME Event Wake Up Power on Function Resume by AlarmPCI 1 IRQ Assignment PnP/PCI ConfigurationsCurrent CPU/SYSTEM FAN Speed RPM Current CPU/System TemperaturePC Health Status Current VoltageV Vcore / DDR25V / +3.3V / +12VFrequency/Voltage Control Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen Bios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the ALi RAID BiosMain Menu Create RAID 0 Striping for PerformanceEnglish Create RAID 1 Mirroring for Reliability Create Jbod for integrated Capacity Rebuild RAID Array Delete RAID Settings & PartitionDelete All RAID Settings & Partition Installing the RAID drivers 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English English English English English Taiwan Headquarters Contact UsChina Shanghai