Gigabyte GA-K8U-939 user manual English

Page 67

Next, the Array Name input line appears for the user to key in a name for the newly created array. The effective characters for an array name is 0-9, A-Z, a-z, space and underscore.

		RAID BIOS Setup Utility (c) 2004 ALi Corporation									www.ali.com.tw
	Create RAID 0 Striping		for Performance
	Create RAID 1 Mirroring for Reliability
	Create JBOD for integrated Capacity							SPACE :		Select
	Stripe Size				64K			SPACE :		Select
	Delete RAID Settings & Partition						,		:	Moving Cursor
	Delete All RAID Settings & Partition							Enter	:	Select & Finish
	Rebuild RAIDArray							ESC	:	Exit
	Input RAIDName (8 characters) : ALi_RAID
				Drive Model		Mode			Capacity		RAIDArray/Type
	S Channel 1 Master :			ST3120026AS		SATA		1	120034 MB
	s Channel 2 Master : ST3120026AS					SATA 1			120034 MB
	RAID Array A	:		Capacity		RAID Type			Stripe Size		RAID Name
	RAID Array A	:
	RAID Array B	:
	RAID Array C	:

After the RAID array has been created successfully, its information shows up at RAID Array List.

RAID BIOS Setup Utility (c) 2004 ALi Corporation

www.ali.com.tw

Create RAID 0 Striping

for Performance

Create RAID 1 Mirroring for Reliability

Create JBOD for integrated Capacity

SPACE :

Select

Stripe Size

64K

Delete RAID Settings & Partition

,

:

Moving Cursor

Delete All RAID Settings & Partition

Enter

:

Select & Finish

Rebuild RAIDArray

ESC

:

Exit

Drive Model

Mode

Capacity

RAIDArray/Type

Channel 1 Master :

ST3120026AS

SATA

1

120034 MB

Channel 2 Master : ST3120026AS

SATA 1

120034 MB

Capacity

RAID Type

Stripe Size

RAID Name

RAID Array A

:

240 GB

0

64K

ALi_RAID

RAID Array B

:

RAID Array C

:

Before create the RAID Array, you can select the Stripe Size first. The Stripe Size is effective for RAID 0. The user can choose a stripe size from 64KByte, 32KByte, 16KByte(default), 8KByte and 4KByte. If the user uses RAID 0 for most A/V editing application or files, 64KByte is recommended.

English

- 67 -

Appendix

Image 67

Contents GA-K8U-939 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation 939 GA-K8U-939 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector FDD FDD Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BAT BatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center Connector17 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos Game Game ConnectorEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example GA-K8U-939 / Bios Ver. F1 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordTime Standard Cmos FeaturesMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceOnChip Sata OnChip Sata ModeIntegrated Peripherals OnChip AudioOn-Chip Secondary IDE IDE DMA transfer accessOnBoard LAN Boot ROM On-Chip Primary IDEOnboard Parallel port Uart Mode SelectUR2 Duplex Mode Parallel Port ModePME Event Wake Up Power Management SetupModem Ring Resume Power on Function Resume by AlarmPCI 1 IRQ Assignment PnP/PCI ConfigurationsCurrent CPU/SYSTEM FAN Speed RPM Current CPU/System TemperaturePC Health Status Current VoltageV Vcore / DDR25V / +3.3V / +12VFrequency/Voltage Control Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen Bios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the ALi RAID BiosMain Menu Create RAID 0 Striping for PerformanceEnglish Create RAID 1 Mirroring for Reliability Create Jbod for integrated Capacity Delete All RAID Settings & Partition Delete RAID Settings & PartitionRebuild RAID Array Installing the RAID drivers 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English English English English English English Taiwan Headquarters Contact UsChina Shanghai