Gigabyte GA-K8U-939 user manual Power Management Setup, PME Event Wake Up, Modem Ring Resume

Page 38

English

2-4

Power Management Setup

 

 

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

 

Power Management Setup

 

 

 

ACPI Suspend Type

 

[S1(POS)]

 

Item Help

 

AC BACK Function

 

[Soft-Off]

 

Menu Level`

 

Soft-Off by PWRBTN

[Instant-off]

 

 

 

PME Event Wake Up

[Enabled]

 

 

 

 

Modem Ring Resume

[Enabled]

 

 

 

 

Resume by Alarm

 

[Disabled]

 

 

 

x

Date (of Month) Alarm

Everyday

 

 

 

x

Time (hh:mm:ss) Alarm

0 : 0 : 0

 

 

 

 

Hammer Fid control

[StartUp]

 

 

 

 

POWER ON Function

[Disabled]

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

ACPI Suspend Type

 

 

 

 

 

S1(POS)

 

Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)

 

S3(STR)

 

Set ACPI suspend type to S3/STR(Suspend To RAM).

 

 

AC BACK Function

 

 

 

 

 

Soft-Off

 

When AC-power back to the system, the system will be in "Off" state. (Default value)

 

Full-On

 

When AC-power back to the system, the system always in "On" state.

 

Memory

 

When AC-power back to the system, the system will return to the Last state before

 

 

 

AC-power off.

 

 

 

 

 

Soft-Off by PWRBTN

 

 

 

 

 

Instant-off

 

Press power button then Power off instantly. (Default value)

 

 

Delay 4 Sec.

Press power button 4 seconds to Power off. Enter suspend if button is pressed less

 

 

 

than 4 seconds.

 

 

 

PME Event Wake Up

This feature requires an ATX power supply that provides at least 1A on the 5VSB lead.

Disabled

Disable this function.

Enabled

Enable PME as wake up event. (Default value)

Modem Ring Resume

An incoming call via modem can awake the system from any suspend state.

Disabled

Disable Modem Ring Resume function.

Enabled

Enable Modem Ring Resume function. (Default value)

GA-K8U-939 Motherboard

- 38 -

Image 38
Contents GA-K8U-939 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8U-939 Motherboard Layout 939Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBAT Battery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 17 IRGame Game Connector Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example GA-K8U-939 / Bios Ver. F1 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupStandard Cmos Features TimeHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckOnChip Audio OnChip Sata ModeIntegrated Peripherals OnChip SataOn-Chip Primary IDE IDE DMA transfer accessOnBoard LAN Boot ROM On-Chip Secondary IDEParallel Port Mode Uart Mode SelectUR2 Duplex Mode Onboard Parallel portModem Ring Resume Power Management SetupPME Event Wake Up Resume by Alarm Power on FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/System TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen Congratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the ALi RAID Bios Entering the RAID Bios SetupCreate RAID 0 Striping for Performance Main MenuEnglish Create RAID 1 Mirroring for Reliability Create Jbod for integrated Capacity Rebuild RAID Array Delete RAID Settings & PartitionDelete All RAID Settings & Partition Installing the RAID drivers Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English English English English English Contact Us Taiwan HeadquartersChina Shanghai