Gigabyte GA-K8U-939 Entering the Q-FlashTMutility, Task menu for Dual Bios utility, Action bar

Page 56

English

Entering the Q-FlashTMutility:

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Exploring the Q-FlashTM / Dual BIOS utility screen

The Q-Flash / Dual BIOS utility screen consists of the following key components.

Task menu for Dual BIOS utility

Task menu for Q-FlashTMutility

								Dual BIOS utility bar
			Dual BIOS Utility
			Dual BIOS Utility

		Boot From		Main Bios
		Main ROM Type/Size		SST 49LF004A	512K
		Backup ROM Type/Size		SST 49LF004A	512K
		Wide Range Protection		Disable
			Boot From	Main Bios
			Auto Recovery	Enable
			Halt On Error	Disable
			Copy Main ROM Data to Backup
			Load Default Settings
			Save Settings to CMOS					Q-FlashTMutility title

			Q-Flash Utility
			Q-Flash Utility
			Load Main BIOS from Floppy					bar
			Load Backup BIOS from Floppy					bar
			Save Main BIOS to Floppy
			Save Backup BIOS to Floppy					Action bar
			Save Backup BIOS to Floppy
		Enter : Run	:Move	ESC:Reset	F10:Power Off
		Enter : Run	:Move	ESC:Reset	F10:Power Off

Task menu for Dual BIOS utility:

Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a task and pressing Enter key on your keyboard to enable execution of the task.

Task menu for Q-Flash utility:

Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu- tion of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons mentioned on your keyboards to perform these actions.

GA-K8U-939 Motherboard

- 56 -

Image 56

Contents GA-K8U-939 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8U-939 Motherboard Layout 939Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBAT Battery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 17 IRGame Game Connector Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example GA-K8U-939 / Bios Ver. F1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckOnChip Sata Mode Integrated PeripheralsOnChip Audio OnChip SataIDE DMA transfer access OnBoard LAN Boot ROMOn-Chip Primary IDE On-Chip Secondary IDEUart Mode Select UR2 Duplex ModeParallel Port Mode Onboard Parallel portModem Ring Resume Power Management SetupPME Event Wake Up Resume by Alarm Power on FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentCurrent CPU/System Temperature PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen Congratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the ALi RAID Bios Entering the RAID Bios SetupCreate RAID 0 Striping for Performance Main MenuEnglish Create RAID 1 Mirroring for Reliability Create Jbod for integrated Capacity Rebuild RAID Array Delete RAID Settings & PartitionDelete All RAID Settings & Partition Installing the RAID drivers Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English English English English English Contact Us Taiwan HeadquartersChina Shanghai